A water supply distribution system for an averagely-populated township is to be designed for
A
Maximum daily demand
B
Maximum hourly demand and fire demand
C
Average demand
D
Maximum daily demand and fire demand or maximum hourly demand, whichever is higher
Question 2Single Answer
A combined sewerage system is more appropriate for developed areas where
A
Rainfall occurs for a very few days in a year
B
Rainfall occurs almost uniformly throughout the year
C
Air temperatures are nearly uniform throughout the year
D
Air temperatures through the year include extremes during certain runs of days
Question 3Single Answer
100 m3 of sludge holds a moisture content of 95%. If its moisture content chagnes to 90%, the volume of this sludge will then be
A
40.5m3
B
50m3
C
75m3
D
94.7m3
Question 4Single Answer
The design overflow rate of a sedimentation tank is chosen considering
A
Flow rate through the tank
B
Diameter of the particle intended to be removed
C
Volume of the sedimentation tank
D
Detention time in the tank
Question 5Single Answer
Consider the following statements in respect of flow equalization in a waste water treatment plant :
1. Biological treatment is enhanced because shock loadings are eliminated or minimized
2. Flow equalizations is an attractive option for upgrading the performance of overloaded treatment plants.
3. Inhibiting substances can be diluted and pH can be stabilized
4. Thickening performance of primary sedimentation tanks following grit removal is improved.
Which of the above statements are correct?
A
1, 2, 3 and 4
B
1, 2 and 3 only
C
1, 2 and 4 only
D
3 and 4 only
Question 6Single Answer
A drain carrying 5m3/s of wastewater with its BOD of 100mg/l joins a stream carrying 50 m3/ s flow with its BOD of 5mg/l. What will be the value of the BOD of the combined flow after complete mixing?
A
3.6 mg/l
B
13.6 mg/l
C
33.6 mg/l
D
53.6 mg/l
Question 7Single Answer
Consider the following statements in respect of aerated grit chamber:
1. The grit accumulates at the bottom in advancing spiral-flow aeration tanks, location ally preceded by grit chambers, led to the eventual development of aerated grit chambers.
2. The excessive wear on grit handling equipment is a major factor for the popularity of aerated grit chambers.
3. Aerated grit chambers are designed to provide detention period of 1 minute at maximum rate of flow.
4. Diffusers are located at 0.45 m to 0.6 m above the bottom of teh chamber.
Which of the above statements are correct?
A
1, 2 and 3 only
B
3 and 4 only
C
1, 2 and 4 only
D
1, 2, 3 and 4
Question 8Single Answer
Quick sand condition occurs when
A
the void ratio of the soil becomes 1.0
B
the upward seepage pressure in soil becomes zero
C
the upward seepage pressure in soil becones equal to the saturated unit weight of he soil
D
the upward seepage pressure in soil becomes equal to he submerged unit weight of the soil
Question 9Single Answer
The side of a square land was measured as 150 m and is in error by 0.05 m. What is the corresponding error in the computed area of the land.
A
5 m2
B
25 m2
C
10 m2
D
20 m2
Question 10Single Answer
Consider the following statements in respect of anaerobic sludge digester:
1. It is less expensive compared to several other methods available.
2. Processing of separable solids impacts the environment to a minimum
3. Quantity of separated solids requiring disposal is minimal
4. Digested sludge is very readily dewaterable.
Which of the above statements are correct?
A
1, 2, 3 and 4
B
1, 2 and 3 only
C
3 and 4 only
D
1, 2 and 4 only
Question 11Single Answer
Consider the following statements as regards a Septic Tank
1. The size required is large and uneconomical when serving more than roughly 100 persons.
2. It can remove around 90% of BOD and 80% of suspended solids.
3. As compared to the sludge holdings of a plain sedimentation tank, a septic tank can hold about 90% less of sludge volume.
4. Frequent removal of sludge is not required Which of the above statements are correct?
A
1 and 2
B
1 and 3
C
3 and 4
D
1 and 4
Question 12Single Answer
Sewage sickness relates to
A
Toxicity of sewage interfering with ‘response’ to treatment
B
Destruction of aquatic flora and fauna due to gross pollution of receiving bodies of water by the sewage
C
reduction in the waste purifying capacity of the soil
D
Clogging of pores in soil due to excessive application of sewage leading to obstruction of land aeration thereby leading to septic conditions in the land
Question 13Single Answer
The waste water of a certain large colony contains 10–5.6 mmol of OH– ions at 25ºC. The pH of this sample is
A
8.6
B
7.9
C
5.4
D
4.5
Question 14Single Answer
Consider the relevance of the following features for causing photochemical smog:
1. Air stagnation
2. Abundant sunlight
3. High concentration of NOx in atmosphere.
4. High concentration of SO2 in atmosphere. Which of the above features are correct?
A
1, 2 and 4 only
B
3 and 4 only
C
1, 2 and 3 only
D
1, 2, 3 and 4
Question 15Single Answer
Consider the following statements related to ecology:
1. All the physical, chemical and biological factors that a species needs in order to live and reproduce is called ecological niche.
2. The boundary zone between two ecosystems is known as ecotone.
3. The forests in the Arctics are known as tundra.
4. A biome usually has a distinct climate and life forms adapted to that climate. Biome is more extensive and complex than an ecosystem Which of the above statements are correct?
A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 16Single Answer
Consider the following laws of ecology suggested by Barry Commoner:
1. Everything is connected to everything else.
2. Everything must go somewhere.
3. Nature knows best.
4. There is no such thing as a free lunch.
Which of the above statements are correct?
A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 17Single Answer
For a hydraulically efficient rectangular channel of bed width 5m, the hydraulic radius is
A
0.5m
B
1.25m
C
2.75m
D
4.25m
Question 18Single Answer
A soil sample has shrinkage limit of 6%, and the specific gravity of the soil grains is 2.6. The porosity of soil at shrinkage limit is
A
7.5%
B
9.5%
C
13.5%
D
16.5%
Question 19Single Answer
Local mean time of a place of longitude of 42036’ W is 8h 42m 15s AM. The corresponding Green which Mean Time is
A
10 h 32 m 40 s AM
B
11h 32 m 39s PM
C
0 h 32 m 39s PM
D
11 h 32 m 39s AM
Question 20Single Answer
A vertical photograph of a flat area having an average elevation of 250m above mean sea level was taken with a camera of focal length 25 cm. A section line AB 300 m long in the area measures 15cm on the photograph; a tower BP in the area also appears on the photograph. The distance between images of top and bottom of the tower measures 0.5 cm on the photograph. The distance of the image of the top of the tower is 10 cm. The actual height of the tower is
A
10 m
B
15 m
C
20 m
D
25 m
Question 21Single Answer
A transportation trip survey was undertaken between private car, and public car transportation. The proportion of those using private cars is 0.45. While using the public transport, the further choices available are Metro Rail and Mono Rail, out of which commuting by a Mono Rail has a proportion of 0.55. In such a situation, the choice of interest in using a Metro Rail, Mono Rail and private car would be respectively.
A
0.25, 0.3 and 0.45
B
0.45, 0.25 and 0.3
C
0.25, 0.45 and 0.3
D
0.3, 0.25 and 0.45
Question 22Single Answer
An airfoil of surface area 0.1 m2 is tested for lift L in a wind tunnel. (Conditions can be considered as incompressible flow.) At an angle of attack of 5°, with standard air density 1.22 kg/m3, at a speed of 30m/sec, the lift is measured to be 3.2 kgf. What is the lift coefficient? For a prototype wing of area 10 m2, what is the approximate lift at an air speed of 160 kmph at the same angle of attack of 5°?
A
0.572 and 700 kgf
B
0.603 and 700 kfg
C
0.572 and 570 kgf
D
0.603 and 570 kgf
Question 23Single Answer
Two tanks A and B, of constant cross-sectional areas of 10 m2 and 2.5 m2, respectively, are connected by a 5cm pipe, 100 m long, with f = 0.03. If the initial difference of water levels is 3m, how long will it take for 2.5 m3 of water to flow from A to B? Considering entry and exit losses, it can be grossly assumed that the flow velocity, in m/s, through the pipe is 1.75 h, where h is in m, taking g = 10 m/sec2; also, may take area of pipe as 2 × 10–3 m2.
A
535 seconds
B
516 seconds
C
485 seconds
D
467 seconds
Question 24Single Answer
The consistency and flow resistance of a sample of bitumen can be determined through which of the following tests?
A
Viscosity test
B
Penetration test
C
Ductility test
D
Softening point test
Question 25Single Answer
A pipe of 324 mm diameter, having friction coefficient as 0.04, connects two reservoirs with 15 m difference in their water levels through a 1500 m long pipe. What will be the discharge through the pipe?
A
104 lps
B
134 lps
C
165 lps
D
196 lps
Question 26Single Answer
Flexible concrete is a mix comprising of
A
Gravel, filler and 30/40 bitumen
B
Sand, filler and 30/40 bitumen only
C
Gravel, sand, filler and 60/70 bitumen
D
Sand, filler and 60/70 bitumen only
Question 27Single Answer
Consider a soil sample, for which tests yield the following results:
Passing 75 micron sieve 62%
Liquid limit 35%
Plasticity Index 14%
As per the group index classification of soil, what is the soil condition of the above soil sample?
A
Poor
B
Fair
C
Good
D
Excellent
Question 28Single Answer
Consider the following statements regarding ductility of bitumen:
1. Ductility is the property which does not permit bitumen to undergo large deformation without breaking.
2. Bitumens with high ductility are generally adhesive but do not have good cementing properties.
3. Ductility must be ascertained at two different temperatures in order to pronounce on the suitability of the material.
Which of the above statements is/are correct?
A
3 only
B
2 only
C
1 only
D
1, 2 and 3
Question 29Single Answer
What is the critical thickness of a prestressed concrete pavement (using Westergaard’s Corner Load Formula) to support a maximum wheel load of 4200 kg? Allow 10% for impact. Tyre pressure may be taken as 7 kg/cm2. Assume flexural strength of concrete as 50 kg/cm2, factor of safety as 2, subgrade reaction for plastic mix road as 6 kg/cm3, and modulus of elasticity as 3 × 105 kg/cm2.
A
19.6 cm
B
21.6 cm
C
23.6 cm
D
25.6 cm
Question 30Single Answer
At a hydraulic jump, the flow depths are 0.4 m and 5 m at the upstream and downstream, respectively. The channel is wide rectangular. The discharge per unit width is nearly
A
5.8 m2/s
B
6.4 m2/s
C
7.3 m2/s
D
8.3 m2/s
Question 31Single Answer
Overspeed and delay studies on a preselected section of a Highway are conducted by
A
Fast moving car method
B
Enoscope
C
Radar
D
Traffic contours
Question 32Single Answer
The surface tension of water at 20°C is 75 × 10–3 N/m. The difference in water surface within and outside an open-ended capillary tube of 1mm internal bore, inserted at the water surface, would nearly, be
A
7 mm
B
11 mm
C
15 mm
D
19 mm
Question 33Single Answer
Survey of India was publishing toposheets using a scale of
A
1 : 1000
B
1 : 5000
C
1 : 10000
D
1 : 50000
Question 34Single Answer
The maximum speed of a train on B.G. track having a curvature of 3° and cant of 10 cm with allowable cant deficiency of 76 mm, for conditions obtaining in India, is
A
87.6 km/h
B
99.6 km/h
C
76.6 km/h
D
65.6 km/h
Question 35Single Answer
The gradient for a B.G railway line such that the grade resistance together with curve resistance due a 4° curve which will be equivalent to a simple ruling gradient of 1 in 150 is
A
1 : 180
B
1 : 200
C
1 : 300
D
1 : 400
Question 36Single Answer
A pelton wheel works under a head of 400m. Friction loss through the pipe flow is limited to 10%. The coefficient of velocity for the jet is 0.98. What is the velocity of the jet?
Take g = 10 m/s2.
A
83 m/s
B
71 m/s
C
65 m/s
D
56 m/s
Question 37Single Answer
The value of porosity of a soil sample in which the total volume of soil grains is equal to twice the total volume of voids would be
A
30%
B
40%
C
50%
D
60%
Question 38Single Answer
A solid cylinder of length H, diameter D and of relative density S floats in neutral equilibrium in water with its axis vertical. What is the ratio of H to D if S = 0.6?
A
0.86
B
0.72
C
0.52
D
0.46
Question 39Single Answer
In a two-dimensional flow, with its stream function = 2xy, the velocity at a point (3,4) is
A
12.0 units
B
10.0 units
C
8.0 units
D
6.0 units
Question 40Single Answer
An open rectangular tank of dimensions 4m×3m×2m contains water to a height of 1.6m. It is then accelerated along the longer side. What is the maximum acceleration possible without spilling the water? If this acceleration is then increased by 10%, what amount of water will be spilt off?
A
1.472 m/s2 and 0.48 m3
B
1.962 m/s2 and 0.48 m3
C
1.472 m/s2 and 0.52 m3
D
1.962 m/s2 and 0.52 m3
Question 41Single Answer
While conducting the flow measurement using a triangular notch, an error of +2% in head over the notch is observed. The percentage error in the computed discharge would be
A
+7%
B
–3%
C
+5%
D
–4%
Question 42Single Answer
An orifice is located in the side of a tank with its centre 10 cm above the base of the tank. The constant water level is 1.0 m above the centre of orifice. The coefficient of velocity is 0.98. On the issuing jet, the horizontal distance from the vena-contracta to where the jet is 10 cm below vena-contracta is
A
1.62m
B
1.00m
C
0.62m
D
0.32m
Question 43Single Answer
The velocity of water at the outer edge of a 60cm diameter whirlpool, where the water level is horizontal is 2.5 m/s. The velocity of water at a level where the diameter of the whirlpool is 15 cm, is
A
1 m/s
B
5 m/s
C
8 m/s
D
10 m/s
Question 44Single Answer
In a trapezoidal channel with bed width of 2m, and side slopes of 2V on 1H, critical flow occurs at a depth of 1m. What will be the quantity of flow and the flow velocity?
Take g as 10m/s2.
A
7.22 m3/s and 3.10 m/s
B
6.82 m3/s and 2.89 m/s
C
7.22 m3/s and 2.89 m/s
D
6.82 m3/s and 3.10 m/s
Question 45Single Answer
A 7.5 m wide rectangular channel conveys 12 m3/s of water with a velocity of 1.5 m/s. The specific energy head of the flow is
A
1.18m
B
1.78m
C
2.18m
D
2.78m
Question 46Single Answer
The sequent depth ratio in a hydraulic jump formed in a rectangular horizontal channel is 10. The Froude number of the supercritical flow is
A
12.2
B
10.4
C
7.42
D
4.21
Question 47Single Answer
A partially open sluice gate discharges water at 6 m/s with a depth of 40 cm in a rectangular horizontal channel of width 5 m. What would be the post-jump depth of flow on the downstream of the gate by taking g as 10 m/s2?
A
1.51 m
B
1.70 m
C
1.85 m
D
1.95 m
Question 48Single Answer
What is the maximum power available at the downstream end of a pipeline 3 km long, 20 cm in diameter, if water enters at the upstream end at a pressure of 720 m of water, with the taking pipe friction coefficient as 0.03 and g as 10m/s2?
A
770 mhp
B
740 mhp
C
700 mhp
D
660 mhp
Question 49Single Answer
In the design of pipeline the usual practice is to assume that due to aging of pipelines:
1. The effective roughness increases linearly with time
2. The friction factor increases linearly with time 3. The flow through the pipe becomes linearly lesser with time.
Which of the above statements is/are correct?
A
1,2 and 3
B
3 only
C
2 only
D
1 only
Question 50Single Answer
Consider the following statements:
1. In flow through hydro-dynamically smooth pipes, the friction factor f is always a constant. In flow through hydro-dynamically smooth pipes, the friction factor f is always a function of the flow Reynolds number.
3. In a fully developed rough turbulent pipe flow, the friction factor f is a function of relative roughness only.
4. In a fully developed rough turbulent pipe flow, the friction factor f is a function of the flow Reynolds number and relative roughness.
Which of the above statements are correct?
A
1 and 3
B
2 and 3
C
2 and 4
D
1 and 4
Important Questions Package
UPRVUNL JE Exam Online Question Bank Package
Buy UPRVUNL JE Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in UPRVUNL JE question bank 2026 in Online, PDF & Print study material.
+ Free Monthly Current Affairs, GK & more PDF Download
Sr.
Package Name
Amount
1.
UPRVUNL Junior Engineer Exam (Civil) - English
Description : 1000 Question with Answer
₹181[₹500]
2.
UPRVUNL Junior Engineer Exam (Civil) - English
Description : 2000 Question with Answer
₹231[₹500]
3.
UPRVUNL Junior Engineer Exam (Civil) - Hindi
Description : 1000 Question with Answer
₹181[₹500]
4.
UPRVUNL Junior Engineer Exam (Civil) - Hindi
Description : 2000 Question with Answer
₹231[₹500]
Civil
Question 51Single Answer
Consider the following statements :
1. There will be no defects in select grade timbers.
2. The codal values for strength of grade-II timer without defects may be reduced by 37.5%.
3. For timber used as columns, the permissible stress in ungraded timbers is adopted with a multiplying factor of 0.50.
4. In case of wind force and earthquakes, a modification factor of 1.33 is adopted. Which of the above statements are correct ?
A
1 and 3 only
B
1 and 4 only
C
2 and 4 only
D
2 and 3 only
Question 52Single Answer
Consider the following statements regarding timber :
1. The strength of timber increases by Kiln seasoning.
2. Cutting of wood is to be done prior to treatment.
3. Water seasoning is good for prevention of warping.
4. ASCU treatment enhances the strength of wood. Which of the above statements are correct ?
A
1, 2 and 3 only
B
2, 3 and 4 only
C
1, 3 and 4 only
D
1, 2, 3 and 4
Question 53Single Answer
Gase(s) emitted during rotting or decomposition of timber is /are mainly
A
Methane and Hydrogen
B
Hydrogen Sulphide
C
Carbonic acid and Hydrogen
D
Ammonia
Question 54Single Answer
Efflorescence of bricks is due to
A
Excessive burning of bricks
B
High silt content in brick clay
C
High porosity of bricks
D
Soluble salts present in parent clay
Question 55Single Answer
Disintegration of bricks masonry walls is primarily due to
1. Efflorescence
2. Magnesium sulphate in brick
3. Calcined clay admixtures
4. Kankar nodules
Which of the a above statements are correct ?
A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 56Single Answer
Consider the following test :
1. Transverse strength test
2. Water absorption test
3. Impact test
4. Breaking strength test
Which of the above are relevant to testing of tiles ?
A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 57Single Answer
Which of the following statements is/are correct regarding the strength of cement ?
1. Particle sizes less than 3 m increases the viscous nature of the cement.
2. Finer particles in cement can be replaced by fly-ash to improve the strength.
A
1 only
B
2 only
C
Both 1 and 2
D
Neither 1 nor 2
Question 58Single Answer
The constituent compound in Portland cement which reacts immediately with water, and also sets earliest, is
A
Tricalcium silicate
B
Dicalcium silicate
C
Tricalcium aluminate
D
Tetracalcium aluminoferrite
Question 59Single Answer
Which of the following statements are correct with regard to cement mortar ?
1. Workability of cement mortar can be improved by addition of lime.
2. Fly-ash cement is economical in plastering jobs.
3. Addition of saw dust improves workability.
4. Sand in mortar can be replaced by finely crushed fire bricks.
A
1, 2, 3 and 4
B
1, 2 and 3 only
C
3 and 4 only
D
1, 2 and 4 only
Question 60Single Answer
In a concrete mix of proportion 1 : 3 : 6, the actual quantity of sand, which is judged to have undergone 15% bulking, per unit volume of cement, will be
A
3.00
B
3.45
C
4.50
D
6.00
Question 61Single Answer
Which method of curing of concrete is recommendable for rapid gain of strength of concrete ?
A
Sprinkling water
B
Membrane curing
C
High-pressure steam curing
D
Infrared radiation curing
Question 62Single Answer
Which of the following is appropriate as simple field method for assesing consistency of concrete ?
A
Compacting factor
B
Slump test
C
Vee-Bee test
D
Kelly Ball test
Question 63Single Answer
Which of the following are relatable to Autoclaved Aerated Concrete ?
1. Light weight
2. Strong
3 Inorganic
4. Nontoxic
A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 64Single Answer
The workability of concrete becomes more reliable depending on
1. Aggregate-cement ratio
2. Time of transit
3. Grading of the aggregate
A
1 only
B
2 only
C
3 only
D
1, 2 and 3
Question 65Single Answer
Which of the following statements are correct for stresses acting on mutually perpendicular faces of a plane element ?
1. The sum of the normal stresses in mutually perpendicular planes is equal to the sum of the principal stresses.
2. The shearing stresses in two mutually perpendicular planes are equal in magnitude and direction.
3. Maximum shear stress is half of the difference between principal stresses.
A
1, 2 and 3 only
B
1 and 2 only
C
2 and 3 only
D
1 and 3 only
Question 66Single Answer
Which of the following statements are correct?
1. Strain in the direction of applied stress is known as longitudinal strain.
2. Tensile stress results in tensile strain in linear and lateral directions.
3. Strains in all directions perpendicular to the applied stress are known as lateral strain. 4. Ratio of change in volume to original volume is known as volumetric strain.
A
1, 2 and 3 only
B
1, 3 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 67Single Answer
In the cross-section of a timber, cambium layer can occur in
A
Inner Bark and Sap Wood
B
Pith and Heart Wood
C
Sap Wood and Heart Wood
D
Outer Bark and Sap Wood
Question 68Single Answer
Consider the following statements :
1. In the infinitesimal strain theory, dilatation is taken as an invariant.
2. Dilatation is not proportional to the algebraic sum of all normal stresses.
3. The shearing modulus is always less than the elastic modulus.
Which of the above statements is/are correct ?
A
1 only
B
1 and 2 only
C
2 only
D
1, 2 and 3
Question 69Single Answer
Which one of the following represents constitutive relationship ?
A
Vertical displacements in a structure
B
Rotational displacements in a structure
C
System of forces in equilibrium
D
Stress-strain behavior of a material
Question 70Single Answer
Principal stresses at a point are 80 N/mm2 and 40 N/mm2, both tensile. The yield stress in simple tension for this material is 200 N/mm2. The values of factors of safety according to maximum principal stress theory and maximum shear stress theory, respectively, are
A
2.5 and 2.5
B
2.5 and 5
C
5 and 1.67
D
6 and 2.50
Question 71Single Answer
The principal stresses at a point are 2 (tensile) and (compressive), and the stress at elastic limit for the material in simple tension is 210 N/mm2. According to maximum shear strain theory, the value of at failure is
A
70 N/mm2
B
105 N/mm2
C
140 N/mm2
D
210 N/mm2
Question 72Single Answer
Which of the following statements are correct ?
1. Cranes are employable in moving and/or hoisting loads.
2. With the use of dipper and stick, power shovels can be used as hoes.
3. Ovedrive for higher speeds is a facility often used comfortably in the working of a tractor.
4. Clam shells are less desirable than draglines if the material is water-saturated.
A
1 and 4 only
B
1 and 2 only
C
2 and 3 only
D
3 and 4 only
Question 73Single Answer
Two similar bars of Steel and Aluminium are heated to a same temperature. Forces are applied at the ends of the bars to maintain their lengths unaltered. If the ratio of Young’s moduli of Steel and Aluminium is 3, and the ratio of the coefficients of thermal expansion of Steel to that of aluminium is 0.5, what is the stress on the Aluminium bar if the stress on the Steel bar is 100 MPa ?
A
16.7 MPa
B
66.7 MPa
C
136.7 MPa
D
150.0 MPa
Question 74Single Answer
A structural steel beam has an unsymmetrical I-cross-section. The overall depth of the beam is 200 mm. The flange stresses at the top and bottom are 120 N/mm2 and 80 N/mm2, respectively. The depth of the natural axis from the top of the beam will be
A
120 mm
B
100 mm
C
80 mm
D
60 mm
Question 75Single Answer
In the analysis of beams subjected to loads, the point with Nil Bending Moment can be a
1. Point of Contraflexure
2. Point of Maximum Shear Force
3. Point of Inflection
Which of the above statements is/are correct ?
A
1 only
B
2 only
C
3 only
D
1, 2 and 3
Question 76Single Answer
A tractor has a permissible loaded speed of 200 m/minute, which can increase by 25% when the load is removed/deposited. Generally, it is operated at 80% of the permissible speed (loaded unloaded). It works at a location where haul distance is 120 m. Rest allowance per round-trip is taken as 50 seconds on an average. Fixed time per trip, for loading and unloading and turnaround, etc., is 30 seconds. What is its effective cycle time?
A
157 seconds
B
161 seconds
C
173 seconds
D
182 seconds
Question 77Single Answer
The purpose of lateral ties in a short RC column is to
A
Avoid buckling of longitudinal bars
B
Facilitate compaction of concrete
C
Increase the load carrying capacity of the column
D
Facilitate construction
Question 78Single Answer
When a two-hinged parabolic arch is subjected to a rise in ambient temperature, the horizontal thrust at the support will
A
Increase
B
Decrease
C
Remain same
D
Increase or decrease depending on the span
Question 79Single Answer
In the slope-deflection equations, deformations are considered to be caused by
A
Shear forces and bending moments only
B
Axial forces, shear forces and bending moments
C
Axial forces and bending moments only
D
Bending moments only
Question 80Single Answer
The maximum bending moment caused by a set of concentrated moving loads is
A
Always at the midpoint of span
B
Between the midpoint and concentrated load next to the midpoint of the span
C
Not definable
D
Always under a load close to the centroid of the set of loads
Question 81Single Answer
Force method of analysis of a structure is particularly preferred when
1. The degrees of freedom of the structure become large
2. The structure has less number of static, and more number of kinematic, indeterminacies
3. The structure has more numbers of static, and less numbers of kinematic, indeterminacies
A
1 only
B
2 only
C
3 only
D
1, 2 and 3
Question 82Single Answer
Stiffness matrix method is the category of
1. Compatibility method
2. Displacement method
3. Force method
4. Equilibrium method
A
1 and 3 only
B
1 and 4 only
C
2 and 3 only
D
2 and 4 only
Question 83Single Answer
Muller-Breslau Principal for obtaining influence lines is applicable to
1. Statically determinate beams and frame
2. Statically indeterminate structures, the material of which is elastic, and follows Hooke’s law.
3. Any statically indeterminate structure
A
1 and 2 only
B
1 only
C
2 only
D
1 and 3 only
Question 84Single Answer
The plastic neutral axis
1. Divides the given section into two equal halves
2. Divides the given section into two unequal parts
3. Lies on the centroidal axis of the section
A
1 only
B
2 only
C
3 only
D
2 and 3 only
Question 85Single Answer
The plastic moment capacity MP is
A
Less than the yield moment
B
Equal to the yield moment
C
Greater than the yield moment
D
Dependent on section dimensions
Question 86Single Answer
Web crippling is caused by
A
Excessive bending moment
B
Failure of web under point loads
C
Width of flanges
D
Column action of web
Question 87Single Answer
The block shear failure of a bolted joint in tension occurs because of
1. Use of higher shear strength bolts
2. Use of paltes with higher bearing strength
A
1 only
B
2 only
C
Both 1 and 2
D
Neithter 1 nor 2
Question 88Single Answer
As per IS code, the maximum longitudinal pitch allowed in bolted joints of tension members is nominally
A
12 times the thickness of the plate
B
12 times the diameter of the bolt
C
16 times the thickness of the plate
D
16 times the diameter of the bolt
Question 89Single Answer
ISMB 100 (rx = 40 mm, ry = 10 mm) has been used as a column in a industrial shed. Along the minor axis, the the column has restraints in the form of purlins at 1.0 m intervals. Effective length factor along major and minor axes are 1.2 and 1.0, respectively. If the slenderness ratio is restricted to 120, the maximum column height will be
A
1.0 m
B
2.4 m
C
4.0 m
D
4.8 m
Question 90Single Answer
As per IS 800 – 2007, the permitted slenderness ratio for a bracing member in case of hangers shall be
A
140
B
145
C
150
D
160
Question 91Single Answer
A rectangular beam of depth d is under bending. Load has been gradually increased when the top fibre has obtained five times the strain at the first yield. What depth of the beam will still respond by elastic conditions?
A
0.16 d
B
0.20 d
C
0.25 d
D
0.40
Question 92Single Answer
The ultimate moment capacity of a mild steel section is usually
A
Equal to the plastic moment capacity
B
More than the yield moment capacity
C
Let than the yield moment capacity
D
More than the plastic moment capacity
Question 93Single Answer
The portal bracing in a truss-bridge is used to
A
Transfer load from top of end posts to bearings
B
Maintain the rectangular shape of the bridge cross-section
C
Stiffen the structure laterally
D
Prevent the buckling of top chord under side sway
Question 94Single Answer
Consider the following cases in the design of reinforced concrete members in flexure:
1. Over-reinforced section
2. Tension failure
3. Compression failure
4. Under-reinforced section
Which of the above cases are considered for safe design of R.C members in flexure?
A
1 and 2 only
B
2 and 4 only
C
3 and 4 only
D
1 and 3 only
Question 95Single Answer
The bond between steel and concrete is mainly due to
1. Mechanical resistance
2. Pure adhesive resistance
3. Frictional resistance
A
1 and 2 only
B
1 and 3 only
C
2 and 3 only
D
1, 2 and 3
Question 96Single Answer
The carbonation process is demonstrated more by
A
Atmospheric corrosion
B
Chloride corrosion
C
Stress corrosion
D
Hydrogen embrittlement
Question 97Single Answer
When a sprially reinforced short column is loaded axially, the concrete inside the core is subjected to
A
Bending and compression
B
Biaxial compression
C
Triaxial compression
D
Uniaxial compression
Question 98Single Answer
In a reinforced concrete section, shear stress distribution is diagrammatically
A
Wholly Parabolic
B
Wholly Rectangular
C
Parabolic above NA and Rectangular below NA
D
Rectangular above NA and Parabolic below NA
Question 99Single Answer
As per IS 456 – 2000, the maximum permissible shear stress, TCmax' is based on
A
Diagonal tension failure
B
Diagonal compression failure
C
Flexural tension failure
D
Flexural compression failure
Question 100Single Answer
Footings shall be designed to sustain the
1. Applied loads
2. Moments and forces under relatable loading conditions
3. Induced reactions
A
1and 2 only
B
1 and 3 only
C
2 and 3 only
D
1, 2 and 3
Question 101Single Answer
One bag of Portland cement, 50 kg in weight, would normally have a bulk volume of
A
30 l
B
35 l
C
40 l
D
45 l
Question 102Single Answer
AsCu, a preservative for wood, developed by the Forest Research Institute, Dehradun, comprises of chemicals:
A
1 : 1 : 1
B
1 : 2 : 3
C
1 : 2 : 4
D
1 : 3 : 4
Question 103Single Answer
Consider the following statements related to autoclave bricks:
1.Less water absorption compared to other bricks.
2.Noise reduction
3.It is cheap compared to other types of bricks.
4.Requirement of bulk volume of mortar in joints being relatively less compared to other types of brick masonry.
5.Not recommended for outer walls.
Which of the above statements are relevant to the use of ‘autoclave’ bricks?
A
1, 2 and 4
B
1, 3 and 5
C
2, 3 and 4
D
2, 4 and 5
Question 104Single Answer
The minimum number of annular rings to be seen in every 2.54 cm in the radial direction from the core for timber to be classified as ‘Dense’ is
A
10
B
20
C
25
D
30
Question 105Single Answer
If the actual thickness of a brick masonry wall is 19 cm, its effective length is 2.70 m, its effective height is 2.82 m and its code specified stiffening coefficient is 1.2 then, for design considerations, the slenderness ratio of the wall will be taken as
A
11.8
B
12.4
C
14.2
D
14.8
Question 106Single Answer
Consider the following forms of water in a hydrated cement paste:
1.Capillary water
2.Chemically combined water
3.Interlayer water
4.Adsorbed water
Which of the above forms of water will, on its/their removal, cause shrinkage of the paste?
A
1, 2 and 3
B
1, 2 and 4
C
2, 3 and 4
D
1, 3 and 4
Question 107Single Answer
Consider the following statements:High early strength of cement is obtained as a result of
1.Fine grinding.
2.Decreasing the lime content
3.Burning at higher temperature
4.Increasing the quality of gypsum.
Which of the above statements are correct?
A
1 and 2
B
1 and 3
C
2 and 3
D
3 and 4
Question 108Single Answer
Consider the following statements related to ‘composite mortar’:
1.Addition of lime to cement mortar improves its workability
2.Composite mortar is obtained by adding 10% by weight of cement and mixing with water.
3.Composite mortar is not preferred in tall buildings.
4.Mechanical grinding is essential for developing composite mortar.Which of the above statements are true in this case?
A
1, 2 and 3 only
B
1, 3 and 4 only
C
2, 3 and 4 only
D
1, 2, 3 and 4
Question 109Single Answer
Consider the following statements related to ‘non-destructive testing’ of concrete:
1.Indentation test is used to assess the quality of concrete.
2.Resonant Frequency Method is based on a laboratory test.
3.Compressive strength of concrete is estimated through Pulse Velocity Measurement.
4.Dynamic modulus of Elasticity is determined by a Sonometer Test.
5.Thickness of concrete can be estimated by in-situ Rebound Hammer Test.
Which of the above statements are correct?
A
1, 2 and 3 only
B
1, 2 and 5 only
C
1, 2, 3 and 4 only
D
1, 2, 3, 4 and 5
Question 110Single Answer
What is the amount of water required for a workable RC of mix 1 : 2: 4 by weight., when W/C is 0-60 and unit weight of concrete is 2400 kg/m3?
A
165 l
B
205 l
C
245 l
D
285 l
Question 111Single Answer
Which IS code is used for classification of timber for seasoning purposes?
A
IS : 4970-1973
B
IS : 1708-1969
C
IS : 1141-1958
D
IS : 399-1963
Question 112Single Answer
Consider the following with regard to the application of preservation of timber:
1.Increase in the life span of the member
2.Increase in the strength of the timber
3.Removal of moisture
4.Prevention of growth of fungi by killing them
Which of the above are correct?
A
1, 2, 3 and 4
B
2 and 4 only
C
1 and 4 only
D
2 and 3 only
Question 113Single Answer
The plies in plywood are so placed that the grains of each ply are
A
Parallel to each other
B
At right angle to one another
C
45° oblique to adjacent grain
D
Not constrained by any consideration
Question 114Single Answer
Which of the following is an ODD one as regards ‘requirement of good brick-earth’?
A
It must be free from lumps of lime
B
It should not be mixed with salty water
C
It must be non-homogeneous
D
It should not contain vegetable and organic matter
Question 115Single Answer
The compressive strength of heavy-duty bricks, as per IS : 2980-1962, should not be less than
A
440 kg/cm2
B
175 kg/cm2
C
100kg/cm2
D
75kg/cm2
Question 116Single Answer
Consider the following statements:
1.Brickwork will have high water tightness.
2.Brickwork is preferred for monument structures.
3.Bricks resist fire better than stones
4.Bricks of good quality shall have thin mortar bonds.
Which of the above statements are correct?
A
1 and 2
B
3 and 4
C
2 and 3
D
1 and 4
Question 117Single Answer
Consider the following statements:A good soil for making bricks should contain
1.30% alumina
2.10% lime nodules
3.Only small quantity of iron oxides
4.15% magnesia
Which of the above statements are correct?
A
1 and 2 only
B
1 and 3
C
1, 2 and 4
D
2, 3 and 4
Question 118Single Answer
Which compound of cement is responsible for strength of cement?
A
Magnesium oxide
B
Silica
C
Alumina
D
Calcium sulphate
Question 119Single Answer
Which type of cement is recommended in large mass concrete works such as a dam?
A
Ordinary Portland
B
High Alumina
C
Low-heat Portland
D
Portland Cement
Question 120Single Answer
Consider the following statements regarding ‘setting of cement’:
1.Low-heat cement sets faster than OPC.
2.Final setting time decides the strength of cement
3.Initial setting time of Portland Pozzollona is 30 minutes
4.Air-induced setting is observed when stored under damp conditions.
4.Addition of gypsum retards the setting time.
Which of the above statements are correct?
A
1, 2 and 3
B
2, 3 and 4
C
3, 4 and 5
D
2, 3 and 5
Question 121Single Answer
Consider the following statements regarding ‘strength of cement’:
1.Strength test on cement is made on cubes of cement-sand mix.
2.Water to be used for the paste is 0.25 P, where P is the water needed for normal consistency.
3.The normal consistency is determined on Le Chatelier’s principle.
4.Cubes are cast in two layers in leak-proof moulds further compacted in each layer by vibration on a machine.
Which of the above statements are correct?
A
1 and 2
B
2 and 3
C
1 and 4
D
3 and 4
Question 122Single Answer
Which of the following ingredients refer to binding material of mortar?
1.Cement
2.Lime
3.Sand
4.Ashes
Select the correct answer using the code given below.
A
1 and 4
B
3 and 4
C
1 and 2
D
2 and 3
Question 123Single Answer
Consider the following statements:
1.Bricks in masonry are bound by mortar.
2.Mortars make brick damp-proof.
3.Strength of brick in masonry is improved by plastering.
4.Addition of lime improves workability.
5.Marine construction needs sulphate-resistant cement mortar.
Which of the above statements are relevant for ‘cement mortar’?
A
1, 2 and 3
B
2, 3 and 4
C
1, 4 and 5
D
3, 4 and 5
Question 124Single Answer
Consider the following parameters of concrete:
1.Impermeability
2.Compactness
3.Durability
4.Desired consistency
5.Workability
Which of the above parameters are relevant for ‘water-cement ratio’?
A
4 and 5
B
1 and 2
C
2 and 4
D
3 and 5
Question 125Single Answer
Consider the following statements:Presence of Na2O and K2O in concrete leads to
1.Expansive reaction in concrete
2.Cracking of concrete
3.Disruption of concrete
4.Shrinkage of concrete
Which of the above statements are correct?
A
1 and 2 only
B
2 and 3 only
C
1, 2 and 3
D
3 and 4
Question 126Single Answer
The maximum total quantity of dry aggregate by mass per 50 kg of cement, to be taken as the sum of the individual masses of fine and coarse aggregates (kg), for M20 grade of concrete is
A
625
B
480
C
330
D
250
Question 127Single Answer
Absorption capacity of an aggregate refers to the difference expresses in appropriate proportion in water content between
A
A wet aggregate and a dry aggregate
B
A dry aggregate and a wet aggregate
C
A saturated surface-dry aggregate and a dry aggregate
D
A saturated surface-dry aggregate and an over dry aggregate
Question 128Single Answer
Consider the following statements concerning ‘elasticity of concrete’:
1.Stress-strain behavior of concrete is a straight line up to 10% ultimate stress.
2.Strain determination is obtained from tangent modulus.
3.Modulus of elasticity of concrete is also called as secant modulus.
Which of the above statements are correct?
A
1, 2 and 3
B
1 and 3 only
C
1 and 2 only
D
2 and 3 only
Question 129Single Answer
Consider the following statements :The addition of CaCl2 in concrete results in
1.Increased shrinkage
2.Decreased setting time
3.Decreased shrinkage
4.Increased setting time
Which of the above statements are correct?
A
1 only
B
2 and 3
C
3 and 4
D
1 and 2
Question 130Single Answer
Which of the following statements are correct ?
1.Knots in a tree affect the continuity of fibres.
2.Nail knots do not influence the strength of timber.
3.Druxiness of wood is not a defect.
4.Tall trees with twisted fibers give good timber for poles.
A
1, 2, 3 and 4
B
1, 2 and 4 only
C
1, 2 and 3 only
D
2, 3 and 4 only
Question 131Single Answer
Consider the following statements:
1. IS 3583 refers to Burnt Clay Paving Bricks.
2. IS 5779 refers to Burnt Clay Soling Bricks.
3. IS 3952 refers to Burnt Clay Hollow Bricks.
4. IS 2222 refers to Burnt Clay Lay Bricks.
Which of the above statements are correct?
A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 132Single Answer
Consider the following statements:
1. A high aggregate impact value indicates strong aggregates.
2. A low aggregate crushing value indicates high crushing strength of aggregates.
3. Aggregates having elongation index values greater than 15% are generally considered suitable for pavement construction.
4. Flakiness index of aggregates should not be less than 25% for use in road construction.
Which of the above statements are correct?
A
2 and 3 only
B
2 and 4 only
C
1 and 3 only
D
1 and 4 only
Question 133Single Answer
Consider the following statements regarding refractory bricks in furnaces:
1. The furnace is fired at temperatures more than 1700°C.
2. Silica content in the soil should be less than 40%.
3. Water absorption of bricks should not exceed 10%
4. Chrome bricks are known as basic bricks. Which of the above statements are correct?
A
1 and 2 only
B
2 and 4 only
C
1 and 3 only
D
3 and 4 only
Question 134Single Answer
Consider the following statements about lime:
1. Calcination of limestone results in quick lime.
2. Lime produced from pure variety of chalk is hydraulic lime.
3. Hydrated lime is obtained by treating quick lime with water.
Which of the above statements are correct?
A
1, 2 and 3
B
1 and 2 only
C
2 and 3 only
D
1 and 3 only
Question 135Single Answer
Consider the following statements:
1. If more water is added to concrete for increasing its workability, it results into concrete of low strength.
2. No slump is an indication of a good workable concrete.
3. Higher the slump of concrete, lower will be its workability.
4. Workability of concrete is affected by water content as well as water-cement ratio.
Which of the above statements are correct?
A
1 and 3 only
B
2 and 3 only
C
1 and 4 only
D
2 and 4 only
Question 136Single Answer
Pozzolana used as an admixture in concrete has the following advantages:
1. It improves workability with lesser amount of water.
2. It increases the heat of hydration and so lets the concrete set quickly.
3. It increases the resistance of concrete to attack by salts and sulphates.
4. It leaches out calcium hydroxide.
Select the correct answer using the codes given below:
A
1, 2 and 3 only
B
1, 2 and 4 only
C
1, 3 and 4 only
D
2, 3 and 4 only
Question 137Single Answer
Consider the following statements regarding Cyclopean Concrete:
1. Size of aggregate is more than 150 mm.
2. Size of aggregate is less than 150 mm.
3. High slump.
4. High temperature rise due to heat of hydration.
Which of the above statements are correct?
A
1 and 3 only
B
1 and 4 only
C
2 and 3 only
D
2 and 4 only
Question 138Single Answer
A chain, working a crane, has sectional area of 625 mm2 and transmits a load of 10 kN. When the load is being lowered at a uniform rate of 40 m/min, the chain gets jammed suddenly at which time the length of the chain unwound is 10m. Assuming E = 200 GPa, the stress induced in the chain due to this sudden jamming is
A
100.6 N/mm2
B
120.4 N/mm2
C
140.2 N/mm2
D
160.0 N/mm2
Question 139Single Answer
In mild steel specimens subjected to tensile test cycle, the elastic limit in tension is raised and the elastic limit in compression is lowered, This is called
A
Annealing effect
B
Bauschinger effect
C
Strain rate effect
D
Fatigue effect
Question 140Single Answer
Consider the following statements :
1. The shear stress distribution across the section of a circular shaft subjected to twisting varies parabolically.
2. The shear stress at the centre of a circular shaft under twisting moment is zero
3. The shear stress at the extreme fibres of a circular shaft under twisting moment is maximum.
Which of the above statements is/are correct?
A
1, 2 and 3
B
1 only
C
2 only
D
3 only
Question 141Single Answer
The span of a cantilever beam is 2m. The cross-section of the beam is a hollow square with external sides 100 mm; and its 1 = 4 × 105 mm4. The safe bending stress for the beam material is 100 N/mm2. The safe concentrated load at the free end would be
A
100 N
B
200 N
C
300 N
D
400 N
Question 142Single Answer
Consider the following statements in respect of arched construction made of voussoirs:
1. The superimposed load is transferred to the sidewalls only by the strength of cohesion of the mortar between the voussoirs.
2. The arch may fail under crushing when the compressive stress or thrust in it exceeds the safe crushing strength of the voussoir material.
3. Every element in the arch is subjected to compression only.
4. Failure of the arch due to the sliding of any voussoir past the adjacent one due to transverse shear can be avoided by reducing the height of the voussoirs.
Which of the above statements are correct?
A
1 and 4 only
B
1 and 3 only
C
2 and 4 only
D
2 and 3 only
Question 143Single Answer
Which of the following are examples of indeterminate structures?
1. Fixed beam
2. Continuous beam
3. Two-hinged arch
4. Beam overhanging on both sides
Select the correct answer using the codes given below:
A
1, 2 and 3 only
B
1, 2 and 4 only
C
1, 3 and 4 only
D
2, 3 and 4 only
Question 144Single Answer
A cantilever beam, 3m long, carries a uniformly distributed load over the entire length. If the slope at the free end is 1°, the deflection at the free end is
A
49.27 mm
B
39.27 mm
C
30.27 mm
D
20.27 mm
Question 145Single Answer
The maximum bending moment at a given section, in which a train of wheel loads moves occurs when the average load on the left segment is
1. Equal to the average load on the right segment.
2. More than the average load on the right segment.
3. Less than the average load on the right segment.
Select the correct answer using the codes given below:
A
1, 2 and 3
B
1 only
C
2 only
D
3 only
Question 146Single Answer
A single degree of freedom system of mass 22 kg and stiffness 17 kN/m vibrates freely. If damping in the system is 2%, the cyclic frequency and the damped circular frequency, respectively, are nearly
A
0.4 Hz and 0.88 rad/sec
B
0.88 Hz and 27.8 rad/sec
C
4.4 Hz and 27.8 rad/sec
D
0.88 Hz and 0.88 rad/sec
Question 147Single Answer
A cable of insignificant weight, 18 m long, is supported at its two ends, 16m apart, at the same level. The cable supports at its mid-reach a load of 120 N. The tension in the cable is nearly
A
136 N
B
131 N
C
131 N
D
121 N
Question 148Single Answer
The design strength of a tension member is governed by
1. Rupture at a critical section
2. Yielding of gross area
3. Block shear of end region
Select the correct answer using the codes given below:
A
1 only
B
2 only
C
3 only
D
1, 2 and 3
Question 149Single Answer
A beam-column is alternately bent either (1) in single curvature, or (2) in double curvature. The secondary moments induced are to be compared. These are indicated SM1 and SM2 as per the conditions (1) and (2) respectively
A
SM1 > SM2
B
SM1 < SM2
C
SM1 = SM2
D
Cannot be ascertained
Question 150Single Answer
Gantry girders can be designed
1. As laterally supported beams.
2. As laterally unsupported beams.
3. By using channel sections.
Select the correct answer using the codes given below:
A
1,2 and 3
B
1 and 2 only
C
2 and 3 only
D
1 and 3 only
General Knowledge
Question 151Single Answer
Yojna a weekly journal
A
Ministry of Finance
B
Ministry of Information and Broadcastin
C
Ministry of Rural Development
D
Planning Commission
Question 152Single Answer
Kurukshetra a journal on rural development is published by
A
Ministry of Finance
B
Ministry of Information and Broadcastin
C
Ministry of Rural Development
D
Planning Commission
Question 153Single Answer
Devaluation of a currency means
A
Fixing the value of the currency in conjuction with the movement in the value of a basket of predetermined currencies
B
Reduction in the value of a currency vis-à-vis major internationally traded currencies
C
Fixing the value of currency in multilateral consultaion with the IMF the World Bank and major trading partners
D
Permitting the currency to seek its worth in the international market
Question 154Single Answer
In India rural incomes are generally lower than the urban incomes, which of the following reasons account for this
1. a large number of farmers are illiterate and know little about scientific agriculture
2. prices of primary products are lower than those of manufactured products
3. Investments in agriculture has been low when compared to investment in industry
A
1 and 3
B
2 and 3
C
1 and 2
D
1,2 and 3
Question 155Single Answer
Which of the following programmes aims at the promotion of savings among rural women
A
Rashtriya Mahila Kosh
B
Indira Mahila Yojna
C
Jawahar Rozgar Yojna
D
Mahila Samridhi Yojna
Question 156Single Answer
Copper tools from which age were found in Meerut and Saharanpur?
A
Mesolithic age
B
Paleolithic age
C
Neolithic age
D
Chalcolithic age
Question 157Single Answer
Which of the following centres of Uttar Pradesh is not related to Indus valley Civilization?
1. Kalibanga 2.Lothal
3. Alamgirpur 4.Hulas
A
Codes
1, 2, 3 and 4
B
1 and 2
C
2 and 3
D
3 and 4
Question 158Single Answer
Which site was discovered by Bharat Sevak Samaj on the bank of river Hindon?
A
Alamgirpur
B
Belan Valley
C
Baghrikhor
D
Morhana Mountain
Question 159Single Answer
Kosala (Ayodhya) mentioned Rama story' was related to which of the following dynasties?
A
Videhi
B
Ikshvaku
C
Chandel
D
Kurd
Question 160Single Answer
Which of the following Buddhist Literatures mentions the Mahajanapadas?
A
Bhagavati Sutra
B
Jataka
C
Anguttara Nikaya
D
Garbhavakranti Sutra
Question 161Single Answer
On what date did India celebrate the 9th anniversary of the Goods and Services Tax (GST) implementation?
A
July 1, 2026
B
June 30, 2026
C
July 2, 2026
D
June 29, 2026
Question 162Single Answer
Which global event is India participating in with Sweden as a partner?
A
Venus Orbiter Mission 'Shukrayaan'
B
Chandrayaan-4
C
Gaganyaan crewed mission
D
Mars Orbiter Mission-2
Question 163Single Answer
Who became India's 97th Chess Grandmaster in late June 2026?
A
Gukesh D
B
Praggnanandhaa R
C
Harshavardhan G.B.
D
Arjun Erigaisi
Question 164Single Answer
What major merger was approved by the boards of PFC and REC Limited on June 30, 2026?
A
Merger with SBI
B
Merger into a single power financing entity
C
Merger with NTPC
D
Merger with IREDA
Question 165Single Answer
Which initiative was launched at the Rashtriya Gramin Vikas Sammelan 2026 for rural women SHGs?
A
Lakhpati Didi App
B
Digital India Rural Scheme
C
PM Kisan Drone Yojana
D
SARAS Shakti Collection and Coffee Table Book
Reasoning
Question 166Single Answer
How many such pairs of letters are there in the word ‘CLEANLINESS’ each of the which has as many letters between them in the word as they have in the English alphabet, in the same sequence?
A
Two
B
Three
C
Five
D
Four
E
None of these
Question 167Single Answer
Team A has scored more goals than Team B
Team C has scored fewer goals than Team B
Team A has scored fewer goals than Team C .
If the first two statements are true, the third statement is
A
True
B
False
C
Uncertain
D
None
Question 168Single Answer
If it is possible to make only one meaningful word with the second, the third, the sixth and the eight letters of the word FRAGMENT using each only once, which of the following will be the third letter of that word ? If no such word can be formed, give ‘X’ as the answer and if more than one such word can be formed, give ‘Y’ as the answer.
A
A
B
E
C
T
D
X
E
Y
Question 169Single Answer
How many such letters are there in the word ORIENTAL each of which is as far away from the beginning of the word as when they are arranged alphabetically?
A
None
B
One
C
Two
D
Three
E
More than three
Question 170Single Answer
How many such pairs of letters in the word CREDIT each of which has as many letters between them in the word as in the English alphabet?
A
None
B
One
C
Two
D
Three
E
More than three
Question 171Single Answer
How many meaningful words can be made from the letters ‘LMEA’ using each letter only once in each word?
A
None
B
One
C
Two
D
Three
E
More than three
Question 172Single Answer
If it is possible to make only one meaningful word with the first, the second, the seventh and the eighth letters of the word TEMPORAL, which of the following will be the first letter of that word? If more than one such word can be made, give ‘Y’ as the answer and if no such word can be made, give ‘X’ as the answer.
A
T
B
L
C
E
D
Y
E
X
Question 173Single Answer
If the letters of the word HANDOVER are arranged alphabetically from left to right how many letters will remain at the same position?
A
None
B
One
C
Two
D
Three
E
More than three
Question 174Single Answer
How many such pairs of letters are there in the word EXCURSION, each of which has as many letters between them in the word as they have in the English alphabet?
A
None
B
One
C
Two
D
Three
E
More than three
Question 175Single Answer
If it is possible to make only one meaningful word with the first, the second, the third, the sixth and the eighth letters of the word DEVIATION first letter of that word is your answer? If more than one such word can be made formed your answer is ‘A’ and if no such word can be formed your answer is ‘B’.
A
V
B
T
C
E
D
A
E
B
Question 176Single Answer
Passage :
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z .
Which letter in this alphabet is the eighth letter to the right of the letter and which is tenth letter to the left of the last but one letter of the alphabet ?
A
X
B
W
C
I
D
H
Question 177Single Answer
Passage :
Direction : The following question is based on the five words given below:
AND FOR THE BIG SUM (The new words formed after performing the mentioned operations may or may not necessarily the meaningful English words.)
If the third alphabet of each of the words is changed to the next alphabet in the English alphabetical series, which of the following will form a meaningful English word?
A
SUM
B
BIG
C
Both BIG and THE
D
FOR
E
Both FOR and BIG
Question 178Single Answer
Passage :
Direction : The following question is based on the five words given below:
AND FOR THE BIG SUM (The new words formed after performing the mentioned operations may or may not necessarily the meaningful English words.)
If the given words are arranged in the order as they would appear in a dictionary from left to right, which of the following will be second from the right ?
A
AND
B
FOR
C
THE
D
BIG
E
SUM
Question 179Single Answer
Passage :
Direction: The following question is based on the five words given below:
AND FOR THE BIG SUM (The new words formed after performing the mentioned operations may or may not necessarily the meaningful English words.)
If second alphabet in each of the words is changed to next alphabet in the English alphabetical order, how many words having two vowels (same or different vowels) will be formed ?
A
None
B
One
C
Two
D
Three
E
Four
Question 180Single Answer
Passage :
Direction : The following question is based on the five words given below:
AND FOR THE BIG SUM (The new words formed after performing the mentioned operations may or may not necessarily the meaningful English words.)
How many letters are there in the English alphabetical series between the second letter of the word which is second from the right and the second letter of the word which is second from the left of the given words?
A
Two
B
Five
C
Six
D
Nine
E
Three
Hindi
Question 181Single Answer
शुद्ध वर्तनी का चयन कीजिए
A
अधम्र
B
अध्रम
C
अधर्म
D
अध्रिम
Question 182Single Answer
शुद्ध वर्तनी का चयन कीजिए
A
स्थायि
B
स्थायी
C
स्थाई
D
स्थाइ
Question 183Single Answer
वर्तनी की दृष्टि से सही शब्द है?
A
महत्व
B
महतव
C
महत्तव
D
महतत्व
Question 184Single Answer
निम्नलिखित में से शुद्ध छांटिए?
A
आयुष्मान
B
आयुश्मान
C
आयुशमान
D
आयुश्यमान
Question 185Single Answer
शुद्ध शब्द नहीं हैं?
A
कवियत्री
B
कौसल्या
C
एश्वर्य
D
श्रृंगार
Question 186Single Answer
शुद्ध वर्तनी है -
A
पूज
B
पुजय
C
पूज्य
D
पुज्य
Question 187Single Answer
शुद्ध वर्तनी है -
A
अनुसरण
B
अनूशरणन
C
अनुशरण
D
अणुशर
Question 188Single Answer
किस क्रमांक में सभी शुद्ध हैं?
A
एक्य,साप्ताहिक
B
आजीविका,आशीर्वाद
C
आर्शिवाद ,अनूकूल
D
निरिक्षण ,कृपालु
Question 189Single Answer
'उज्वल' शब्द का शुद्ध रूप है ?
A
उज्जव
B
उज्ज्ल
C
उज्ज्वल
D
उजवल
Question 190Single Answer
निम्नलिखित प्रश्न में चार वैकल्पिक वर्तनियाॅ दी गई है?
A
जागृत
B
जाग्रति
C
जाग्रित
D
जाग्रत
Question 191Single Answer
Passage :
प्रश्न में दी गई इटैलिक अशुद्ध वर्तनी का शुद्ध रूप चयन कीजिए।
तुम्हारा यह कथन मात्र अतिश्योक्ती है।
A
अंतोश्योक्ती
B
अतीश्योक्टि
C
अतिश्योक्ति
D
अतिशयोक्ति
Question 192Single Answer
Passage :
प्रश्न में एक शब्द दिया गया है जिसका सन्धि-विच्छेद चार प्रकार से किया गया है। इनमें सें केवल एक ही विकल्प सही है। सही सन्धि-विच्छेद का चयन कीजिए -
बहिष्कार
A
बहि: + कार
B
बहिष + कर
C
बहि + अकार
D
बहि़ + सकार
Question 193Single Answer
Passage :
प्रश्न में एक शब्द दिया गया है जिसका सन्धि-विच्छेद चार प्रकार से किया गया है। इनमें सें केवल एक ही विकल्प सही है । सही सन्धि-विच्छेद का चयन कीजिए -
नाविक
A
नौ + इक
B
ना + इक
C
नो + इक
D
ना + विक
Question 194Single Answer
Passage :
प्रश्न में एक शब्द दिया गया है जिसका सन्धि-विच्छेद चार प्रकार से किया गया है। इनमें सें केवल एक ही विकल्प सही है । सही सन्धि-विच्छेद का चयन कीजिए -
दिगम्बर
A
दि + गम्बर
B
दिगम् + बर
C
दिक् + अम्बर
D
दिग + अम्बर
Question 195Single Answer
Passage :
प्रश्न में एक शब्द दिया गया है जिसका सन्धि-विच्छेद चार प्रकार से किया गया है। इनमें सें केवल एक ही विकल्प सही है । सही सन्धि-विच्छेद का चयन कीजिए -
निराशा
A
निरा + आशा
B
निर् + आशा
C
निर: + आशा
D
निर + आशा
Question 196Single Answer
Passage :
प्रश्न में एक शब्द दिया गया है जिसका सन्धि-विच्छेद चार प्रकार से किया गया है। इनमें सें केवल एक ही विकल्प सही है । सही सन्धि-विच्छेद का चयन कीजिए -
मनोरथ
A
मनो + अर्थ
B
मन: + रथ
C
मन: + अरथ
D
मने + ओरथ
Question 197Single Answer
Passage :
प्रश्न में एक शब्द दिया गया है जिसका सन्धि-विच्छेद चार प्रकार से किया गया है। इनमें सें केवल एक ही विकल्प सही है । सही सन्धि-विच्छेद का चयन कीजिए -
यद्यपि
A
यद्य + आपि
B
य + द्यपि
C
यदि + अपि
D
यद्य + आपि
Question 198Single Answer
Passage :
प्रश्न में एक शब्द दिया गया है जिसका सन्धि-विच्छेद चार प्रकार से किया गया है। इनमें सें केवल एक ही विकल्प सही है । सही सन्धि-विच्छेद का चयन कीजिए -
तिरस्कार
A
तिरस + कार
B
तिर: + कार
C
ति: + कार
D
तिर + कार
Question 199Single Answer
Passage :
प्रश्न में एक शब्द दिया गया है जिसका सन्धि-विच्छेद चार प्रकार से किया गया है। इनमें सें केवल एक ही विकल्प सही है । सही सन्धि-विच्छेद का चयन कीजिए -
स्वार्थ
A
स्व +अर्थ
B
स्वा + अर्थ
C
स्वा + अथ
D
स्व +आर्थ
Question 200Single Answer
Passage :
प्रश्न में एक शब्द दिया गया है जिसका सन्धि-विच्छेद चार प्रकार से किया गया है। इनमें सें केवल एक ही विकल्प सही है । सही सन्धि-विच्छेद का चयन कीजिए -