What was the currency of Hyderabad State during the period of last Nizam ?
A
Ana
B
Nizamia Ana
C
Osmania Sikka
D
Nizamia Sikka
Question 4Single Answer
"Telangana Palle Pragathi" project was launched in the Village of
A
Kowdipally, Medak District
B
Erravalli, Medak District
C
Mulkanoor, Karimnagar District
D
Chevella, Rangareddy District
Question 5Single Answer
Name of the Bank founded by the last Nizam of Hyderabad Mir Osman Ali Khan is
A
Nizam State Bank
B
Hyderabad Provincial Bank
C
Hyderabad Commerical Bank
D
Hyderabad State Bank
Question 6Single Answer
Who construted the 'Masaheba' tank in Hyderabad ?
A
Hayat Bakshi Begum
B
Khanan Bakshi Begum
C
Ameena Bibi
D
Meherunnis
Question 7Single Answer
Who established the State Depressed Classes Association in Hyderabad?
A
Arige Ramaswamy
B
Yathiraj
C
Bhagya Reddy Varma
D
B.S. Venkat Rao
Question 8Single Answer
Which of the following committee was appointed by the VII Nizam to suggest Constitutional Reforms ?
A
Ali Imam Committee
B
Aravamudu Iyengar Committee
C
Pingali Venkataram Reddy Committee
D
Mirza Yar Jung Committee
Question 9Single Answer
Which Landlord donated his lands during the Bhoodan Movement in Telangana ?
A
Visnuri Ramchandra Reddy
B
Katkuri Krishna Rao
C
Pingali Venkat Rao
D
Vedire Ramachandra Reddy
Question 10Single Answer
Who was the incharge of 'port - Cities' during Qutubshahi period ?
A
Ain-Ul-Mulk
B
Shah-Bandhar
C
Dabir
D
Kotwal
Question 11Single Answer
For the maintenace of the Hyderabad Contingent Forces, which area was surrendered to the British by the Nizam's Government ?
A
Aurangabad
B
Warangal
C
Mahaboobnagar
D
Berar
Question 12Single Answer
Who was the founder of the Salarjung Museum in Hyderabad?
A
Salarjung - I
B
Salarjung - II
C
Salarjung - III
D
Osman Ali Khan
Question 13Single Answer
Which of the following district has the lowest HDI (Human Development Index) In Telangana State?
A
Nalgonda
B
Mahaboobnagar
C
Adilabad
D
Khammam
Question 14Single Answer
Which district has the lowest population in Telangana State as per 2011 Census ?
A
Nizamabad
B
Khammam
C
Adilabad
D
Warangal
Question 15Single Answer
Density of population in Telangana as per 2011 Census
A
227 persons per sq. Km.
B
307 persons per sq. Km.
C
325 persons per sq. Km.
D
350 persons per sq. Km.
Question 16Single Answer
Which of the following is the leading Rice crop producing district in Telangana State ?
A
Nalgonda
B
Nizamabad
C
Karimnagar
D
Warangal
Question 17Single Answer
Second largest district in Telangana State, area - wise is
A
Mahaboobnagar
B
Adilabad
C
Karimnagar
D
Khammam
Question 18Single Answer
Least Urbanized district in Telangana as per 2011 Cesus is
A
Adilabad
B
Nalgonda
C
Mahaboobnagar.
D
Medak
Question 19Single Answer
Tank irrigation area predominantly found in the district of
A
Khammam
B
Karimnagar
C
Nizamabad
D
Warangal
Question 20Single Answer
'Gusadi' Dance is popular in which district of Telangana ?
A
Nizamabad
B
Khammam
C
Warangal
D
Adilabad
Question 21Single Answer
The other popular name of Komaravelli Veerabhadra Swamy is
A
Ellanna
B
Mallanna
C
Rajanna
D
Beeranna
Question 22Single Answer
Name the Village of Telangana, in which coal was found for the first time .
A
Bellampalli .
B
Bhupalpalli
C
Yellandu
D
Ramagundam
Question 23Single Answer
Who established the Asian Largest Sugar Factory in Shakkar Nagar ?
A
Sharad Pawar
B
Mir Osman Ali Khan
C
Azam Khan
D
N.T. Rama Rao
Question 24Single Answer
How many Mandals of Khammam District are merged in Andhra Pradesh after bifurcation of the State ?
A
6.
B
7
C
8
D
9.
Question 25Single Answer
Where is the 100 pillar temple located ?
A
Nizamabad
B
Hanmakonda
C
Medak
D
Karimnagar
Question 26Single Answer
The Dandora Movement was launched for the purpose of
A
Sub-classification of Scheduled Castes
B
Sub-classification of Scheduled Tribes
C
Sub-classification of the most Backward classes
D
Abolition of Caste based reservation
Question 27Single Answer
Which district in Telangana has the highest number of cement factories ?
A
Warangal
B
Khammam
C
Nalgonda
D
Nizamabad.
Question 28Single Answer
Munneru River flows through which district of Telangana ?
A
Karimnagar
B
Adilabad
C
Khammam
D
Medak
Question 29Single Answer
In which district of Telangana the Amrabad Tiger Reserve is located ?
A
Karimnagar
B
Mahaboobnagar
C
Adilabad
D
Khammam
Question 30Single Answer
The Gun Park in Hyderabad is built to commemorate
A
The peasants who lost their lives in the Telangana Armed stuggle.
B
The students who lost their lives during the 1969 Telangana Movement.
C
The soldiers who lost their lives during the 1857 revolt.
D
The nationalists who died during the Quit India Movement.
Question 31Single Answer
Which of the following is NOT associated with the Krishna river ?
A
Nagarjuna Sagar Project
B
Srisailam project
C
Pulichintala project
D
Ellampally project
Question 32Single Answer
The Indian Tsunami Early Warning Centre is located at
A
Chennai
B
Hyderabad
C
Kolkata
D
Mumbai
Question 33Single Answer
The first Geographical Indication in Telangana area was registered in respect of the following goods :
A
Pochampally Dress Designs
B
Hyderabadi Haleem
C
Hyderabadi Biryani
D
Pembarti Metal craft
Question 34Single Answer
Who is the famous Oggukatha Artist ?
A
Alekya Punjala
B
Sindu Yellamma
C
Chukka Sattaiah
D
Chukka Ramayya
Question 35Single Answer
In Telangana which district is known for Silver Filigree ?
A
Nizamabad
B
Khammam
C
Warangal
D
Karimnagar
Question 36Single Answer
In Telangana the Nallamala Forests are spread in
A
Adilabad and Nizamabad
B
Mahaboobnagar and Nalgonda
C
Adilabad and Warangal
D
Mahaboobnagar and Rangareddy
Question 37Single Answer
Nataraja Ramakrishna is an expert of which dance form ?
A
Perini Shiva Tandavam
B
Oggu-Katha
C
Kuchipudi
D
Kathakali
Question 38Single Answer
Pillala Marri is situated in the district of
A
Medak
B
Nalgonda
C
Mahaboobnagar
D
Nizamabad
Question 39Single Answer
The first Open university of India was established in
A
Ahmedabad
B
Hyderabad
C
Allahabad
D
New Delhi
Question 40Single Answer
As per 2011 Census density of population in Telangana State is :
A
306
B
350
C
382
D
390
Question 41Single Answer
Hyderabad Tenancy and Agricultural Land Act was enacted in the year
A
1948
B
1950
C
1956
D
1975
Question 42Single Answer
Which district has the highest ST population share in its total population ?
A
Khammam
B
Adilabad
C
Nalgonda
D
Warangal
Question 43Single Answer
Major Source of irrigation for agricultural in the Telangana State :
A
Canals
B
Tanks
C
Wells
D
Water-Harvesting Pits
Question 44Single Answer
As per 2011 Census lowest literacy rate district in Telangana State :
A
Medak
B
Mahaboobnagar
C
Adilabad
D
Khammam
Question 45Single Answer
In Telanagana 'Budubunga' is
A
a tree
B
a bird
C
a type of pot
D
a fruit
Question 46Single Answer
Secundarabad was named after whom ?
A
Secunder pasha
B
Secunder Bakht
C
Secunder Jha
D
Secunder Lodhi
Question 47Single Answer
Identify the commander-in-chief who led the Nizam's Army during the Operation Polo :
A
Laiq Ali
B
Kasim Razvi
C
S.A. Eldruss
D
Mehdi yar Jung
Question 48Single Answer
The Mozam Jahi Market in Hyderabad was named after
A
the second son of Osman Ali khan
B
the first son of Osman Ali khan
C
the brother of Osman Alu khan
D
the grandson of Mehaboob Ali khan
Question 49Single Answer
The Hali Sicca was introduced by
A
Quli Qutub shah
B
Shamirpet
C
Mir Alam
D
Bahadur Yar Jung
Question 50Single Answer
During the 1857 revolt in Hyderabad Turrebaz khan was shot dead at
A
Medak
B
Shamirpet
C
Toopran
D
Bhongir
Important Questions Package
TSPSC Deputy Surveyor Exam Online Question Bank Package
Buy TSPSC Deputy Surveyor Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in TSPSC Deputy Surveyor question bank 2026 in Online, PDF & Print study material.
+ Free Monthly Current Affairs, GK & more PDF Download
Sr.
Package Name
Amount
1.
TSPSC Deputy Surveyor Exam - English
Description : 1500 Question with Answer
₹181[₹500]
2.
TSPSC Deputy Surveyor Exam - English (New)
Description : 1500 Question with Answer
₹181[₹500]
3.
TSPSC Deputy Surveyor Exam Question Bank Book - English (New)
Description : 1000 Question with Answer (Printed Material)
₹390[₹600]
GK
Question 51Single Answer
Khilashapuram in Warangal district was associated with
A
Padmanayakas
B
Sarvai Papanna
C
Akkanna-Madanna
D
Gona Budsa Reddy
Question 52Single Answer
Prataparudra-Yashobushanam was wirtten by
A
Vidyanatha
B
Ketana
C
Potana
D
Thikkana
Question 53Single Answer
Chakali Ailamma fought against the Landlord of
A
Palakurthi
B
Kadivendi
C
Visnur
D
Jangaon
Question 54Single Answer
For which novel Ampa shayya Naveen got 'Kendra Sahitya Academy' award ?
A
Kala Megham
B
Telanganam
C
Shayya
D
Kala Rekhalu
Question 55Single Answer
'Maneru' river is a tributary of
A
Godavari
B
Krishna
C
Penganga
D
Manjeera
Question 56Single Answer
The Devadasi / Jogini system prevalent in Telangana would be violative of which of the fundamental rights ?
A
Right to Equality
B
Right against Exploitation
C
Right to Freedom of Religion
D
Right to Life and Personal Liberty
Question 57Single Answer
Which town was the district head-quarter prior to formation of mahaboobnagar district ?
A
Gadwal
B
Wanaparthy
C
Nagarkurnool
D
Narayanpet
Question 58Single Answer
The total number of tanks/lakes proposed to desilted under the scheme of 'Mission Kakatiya' of Telangana Government :
A
9300
B
8212
C
46500
D
54000
Question 59Single Answer
Who is the author of famous song "Jaya Jayahe Telangana" ?
A
Goreti Venkanna
B
Gaddar
C
Guda Anjaiah
D
Ande Sri.
Question 60Single Answer
Name the pension scheme launched by the Telangana Government .
A
Bharosa
B
Aasara
C
Roshini
D
Sahaya.
Question 61Single Answer
Which country holds the BRICS Chairmanship in 2026?
A
Brazil
B
Russia
C
China
D
India
Question 62Single Answer
What is the theme of India’s BRICS Chairmanship 2026?
A
Inclusive Growth for All
B
Sustainable Global Economy
C
One Earth One Future
D
Building for Resilience, Innovation, Cooperation and Sustainability
Question 63Single Answer
Where was the BRICS Foreign Ministers' Meeting held in May 2026?
A
Mumbai
B
Hyderabad
C
Bengaluru
D
New Delhi
Question 64Single Answer
Which summit on Artificial Intelligence was hosted by India in February 2026?
A
World AI Congress
B
AI Action Summit
C
India AI Impact Summit 2026
D
Global AI Forum
Question 65Single Answer
Where was the India AI Impact Summit 2026 organized?
A
Pragati Maidan, Delhi
B
Vigyan Bhawan, New Delhi
C
Bharat Mandapam, New Delhi
D
Hyderabad International Convention Centre
Question 66Single Answer
Which ministry organized the India AI Impact Summit 2026?
A
Ministry of Science and Technology
B
Ministry of Electronics and Information Technology
C
Ministry of Commerce
D
Ministry of Education
Question 67Single Answer
Which city is expected to host the G20 Summit 2026?
A
New York
B
Washington D.C.
C
Miami
D
Los Angeles
Question 68Single Answer
Which country is scheduled to host the BRICS Summit 2026?
A
China
B
India
C
South Africa
D
Brazil
Question 69Single Answer
Which country is expected to host COP31 Climate Summit 2026?
A
France
B
UAE
C
Germany
D
Turkey
Question 70Single Answer
Which city hosted the Regional AI Impact Conference 2026?
A
Chennai
B
Jaipur
C
Pune
D
Kochi
Question 71Single Answer
The Rajasthan AI-ML Policy 2026 was launched during which conference?
A
Digital India Summit
B
AI Action Summit
C
Regional AI Impact Conference 2026
D
India AI Impact Summit
Question 72Single Answer
Which city hosted the 23rd BioAsia International Summit 2026?
A
Mumbai
B
Chennai
C
Bengaluru
D
Hyderabad
Question 73Single Answer
What was the theme of BioAsia International Summit 2026?
A
AI for Humanity
B
Future of Biotechnology
C
TechBio Unleashed: AI, Automation & the Biology Revolution
D
Digital Health Revolution
Question 74Single Answer
Which city hosted the 9th IONS Conclave of Chiefs 2026?
A
Kochi
B
Mumbai
C
Visakhapatnam
D
Goa
Question 75Single Answer
What was the theme of the 9th IONS Conclave of Chiefs 2026?
A
Maritime Security First
B
Indo-Pacific Cooperation
C
Maritime Cooperation for Humanitarian Support
D
Blue Economy Growth
Civil
Question 76Single Answer
One bag of Portland cement, 50 kg in weight, would normally have a bulk volume of
A
30 l
B
35 l
C
40 l
D
45 l
Question 77Single Answer
AsCu, a preservative for wood, developed by the Forest Research Institute, Dehradun, comprises of chemicals:
A
1 : 1 : 1
B
1 : 2 : 3
C
1 : 2 : 4
D
1 : 3 : 4
Question 78Single Answer
Consider the following statements related to autoclave bricks:
1.Less water absorption compared to other bricks.
2.Noise reduction
3.It is cheap compared to other types of bricks.
4.Requirement of bulk volume of mortar in joints being relatively less compared to other types of brick masonry.
5.Not recommended for outer walls.
Which of the above statements are relevant to the use of ‘autoclave’ bricks?
A
1, 2 and 4
B
1, 3 and 5
C
2, 3 and 4
D
2, 4 and 5
Question 79Single Answer
The minimum number of annular rings to be seen in every 2.54 cm in the radial direction from the core for timber to be classified as ‘Dense’ is
A
10
B
20
C
25
D
30
Question 80Single Answer
If the actual thickness of a brick masonry wall is 19 cm, its effective length is 2.70 m, its effective height is 2.82 m and its code specified stiffening coefficient is 1.2 then, for design considerations, the slenderness ratio of the wall will be taken as
A
11.8
B
12.4
C
14.2
D
14.8
Question 81Single Answer
Consider the following forms of water in a hydrated cement paste:
1.Capillary water
2.Chemically combined water
3.Interlayer water
4.Adsorbed water
Which of the above forms of water will, on its/their removal, cause shrinkage of the paste?
A
1, 2 and 3
B
1, 2 and 4
C
2, 3 and 4
D
1, 3 and 4
Question 82Single Answer
Consider the following statements:High early strength of cement is obtained as a result of
1.Fine grinding.
2.Decreasing the lime content
3.Burning at higher temperature
4.Increasing the quality of gypsum.
Which of the above statements are correct?
A
1 and 2
B
1 and 3
C
2 and 3
D
3 and 4
Question 83Single Answer
Consider the following statements related to ‘composite mortar’:
1.Addition of lime to cement mortar improves its workability
2.Composite mortar is obtained by adding 10% by weight of cement and mixing with water.
3.Composite mortar is not preferred in tall buildings.
4.Mechanical grinding is essential for developing composite mortar.Which of the above statements are true in this case?
A
1, 2 and 3 only
B
1, 3 and 4 only
C
2, 3 and 4 only
D
1, 2, 3 and 4
Question 84Single Answer
Consider the following statements related to ‘non-destructive testing’ of concrete:
1.Indentation test is used to assess the quality of concrete.
2.Resonant Frequency Method is based on a laboratory test.
3.Compressive strength of concrete is estimated through Pulse Velocity Measurement.
4.Dynamic modulus of Elasticity is determined by a Sonometer Test.
5.Thickness of concrete can be estimated by in-situ Rebound Hammer Test.
Which of the above statements are correct?
A
1, 2 and 3 only
B
1, 2 and 5 only
C
1, 2, 3 and 4 only
D
1, 2, 3, 4 and 5
Question 85Single Answer
What is the amount of water required for a workable RC of mix 1 : 2: 4 by weight., when W/C is 0-60 and unit weight of concrete is 2400 kg/m3?
A
165 l
B
205 l
C
245 l
D
285 l
Question 86Single Answer
Which IS code is used for classification of timber for seasoning purposes?
A
IS : 4970-1973
B
IS : 1708-1969
C
IS : 1141-1958
D
IS : 399-1963
Question 87Single Answer
Consider the following with regard to the application of preservation of timber:
1.Increase in the life span of the member
2.Increase in the strength of the timber
3.Removal of moisture
4.Prevention of growth of fungi by killing them
Which of the above are correct?
A
1, 2, 3 and 4
B
2 and 4 only
C
1 and 4 only
D
2 and 3 only
Question 88Single Answer
The plies in plywood are so placed that the grains of each ply are
A
Parallel to each other
B
At right angle to one another
C
45° oblique to adjacent grain
D
Not constrained by any consideration
Question 89Single Answer
Which of the following is an ODD one as regards ‘requirement of good brick-earth’?
A
It must be free from lumps of lime
B
It should not be mixed with salty water
C
It must be non-homogeneous
D
It should not contain vegetable and organic matter
Question 90Single Answer
The compressive strength of heavy-duty bricks, as per IS : 2980-1962, should not be less than
A
440 kg/cm2
B
175 kg/cm2
C
100kg/cm2
D
75kg/cm2
Question 91Single Answer
Consider the following statements:
1.Brickwork will have high water tightness.
2.Brickwork is preferred for monument structures.
3.Bricks resist fire better than stones
4.Bricks of good quality shall have thin mortar bonds.
Which of the above statements are correct?
A
1 and 2
B
3 and 4
C
2 and 3
D
1 and 4
Question 92Single Answer
Consider the following statements:A good soil for making bricks should contain
1.30% alumina
2.10% lime nodules
3.Only small quantity of iron oxides
4.15% magnesia
Which of the above statements are correct?
A
1 and 2 only
B
1 and 3
C
1, 2 and 4
D
2, 3 and 4
Question 93Single Answer
Which compound of cement is responsible for strength of cement?
A
Magnesium oxide
B
Silica
C
Alumina
D
Calcium sulphate
Question 94Single Answer
Which type of cement is recommended in large mass concrete works such as a dam?
A
Ordinary Portland
B
High Alumina
C
Low-heat Portland
D
Portland Cement
Question 95Single Answer
Consider the following statements regarding ‘setting of cement’:
1.Low-heat cement sets faster than OPC.
2.Final setting time decides the strength of cement
3.Initial setting time of Portland Pozzollona is 30 minutes
4.Air-induced setting is observed when stored under damp conditions.
4.Addition of gypsum retards the setting time.
Which of the above statements are correct?
A
1, 2 and 3
B
2, 3 and 4
C
3, 4 and 5
D
2, 3 and 5
Question 96Single Answer
Consider the following statements regarding ‘strength of cement’:
1.Strength test on cement is made on cubes of cement-sand mix.
2.Water to be used for the paste is 0.25 P, where P is the water needed for normal consistency.
3.The normal consistency is determined on Le Chatelier’s principle.
4.Cubes are cast in two layers in leak-proof moulds further compacted in each layer by vibration on a machine.
Which of the above statements are correct?
A
1 and 2
B
2 and 3
C
1 and 4
D
3 and 4
Question 97Single Answer
Which of the following ingredients refer to binding material of mortar?
1.Cement
2.Lime
3.Sand
4.Ashes
Select the correct answer using the code given below.
A
1 and 4
B
3 and 4
C
1 and 2
D
2 and 3
Question 98Single Answer
Consider the following statements:
1.Bricks in masonry are bound by mortar.
2.Mortars make brick damp-proof.
3.Strength of brick in masonry is improved by plastering.
4.Addition of lime improves workability.
5.Marine construction needs sulphate-resistant cement mortar.
Which of the above statements are relevant for ‘cement mortar’?
A
1, 2 and 3
B
2, 3 and 4
C
1, 4 and 5
D
3, 4 and 5
Question 99Single Answer
Consider the following parameters of concrete:
1.Impermeability
2.Compactness
3.Durability
4.Desired consistency
5.Workability
Which of the above parameters are relevant for ‘water-cement ratio’?
A
4 and 5
B
1 and 2
C
2 and 4
D
3 and 5
Question 100Single Answer
Consider the following statements:Presence of Na2O and K2O in concrete leads to
1.Expansive reaction in concrete
2.Cracking of concrete
3.Disruption of concrete
4.Shrinkage of concrete
Which of the above statements are correct?
A
1 and 2 only
B
2 and 3 only
C
1, 2 and 3
D
3 and 4
Question 101Single Answer
The maximum total quantity of dry aggregate by mass per 50 kg of cement, to be taken as the sum of the individual masses of fine and coarse aggregates (kg), for M20 grade of concrete is
A
625
B
480
C
330
D
250
Question 102Single Answer
Absorption capacity of an aggregate refers to the difference expresses in appropriate proportion in water content between
A
A wet aggregate and a dry aggregate
B
A dry aggregate and a wet aggregate
C
A saturated surface-dry aggregate and a dry aggregate
D
A saturated surface-dry aggregate and an over dry aggregate
Question 103Single Answer
Consider the following statements concerning ‘elasticity of concrete’:
1.Stress-strain behavior of concrete is a straight line up to 10% ultimate stress.
2.Strain determination is obtained from tangent modulus.
3.Modulus of elasticity of concrete is also called as secant modulus.
Which of the above statements are correct?
A
1, 2 and 3
B
1 and 3 only
C
1 and 2 only
D
2 and 3 only
Question 104Single Answer
Consider the following statements :The addition of CaCl2 in concrete results in
1.Increased shrinkage
2.Decreased setting time
3.Decreased shrinkage
4.Increased setting time
Which of the above statements are correct?
A
1 only
B
2 and 3
C
3 and 4
D
1 and 2
Question 105Single Answer
Which of the following statements are correct ?
1.Knots in a tree affect the continuity of fibres.
2.Nail knots do not influence the strength of timber.
3.Druxiness of wood is not a defect.
4.Tall trees with twisted fibers give good timber for poles.
A
1, 2, 3 and 4
B
1, 2 and 4 only
C
1, 2 and 3 only
D
2, 3 and 4 only
Question 106Single Answer
Excrescences in wood are
1.Defects found in trees
2.Formed due to injuries inflicted on trees when they are growing
3.Defects which render wood suitable as firewood only
A
1, 2 and 3
B
1 and 2 only
C
1 and 3 only
D
2 and 3 only
Question 107Single Answer
What treatment is adopted for making timber fire-resistant?
A
ASCU treatment
B
Abel’s process
C
Creosoting
D
Tarring
Question 108Single Answer
Deterioration of structure of timber due to dry rot is:
1.Caused by fungi
2.Due to dry-spell after heavy rains
3.Due to attack of termites
4.ndicated by surface stripes on scantlings
A
1 and 2
B
3 and 4
C
2 and 3
D
1 and 4
Question 109Single Answer
Alternate wetting and drying of timber :
1.Results in shrinkage and swelling
2.Brings about wet rot onset
3.Increases the durability
4.Causes transmission of spores from germination
A
1, 2, 3 and 4
B
1, 2 and 4 only
C
1, 2 and 3 only
D
2, 3 and 4 only
Question 110Single Answer
As per I.S. classification, the minimum compressive strength of a first class brick should be
A
75 kg/cm3
B
100kg/cm3
C
125 kg/cm3
D
150 kg/cm3
Question 111Single Answer
When provided with alternating courses of (a) all headers and (b) all stretchers, the front elevation of such brick masonry is designated as
A
English bond
B
Single Flemish bond
C
Double Flemish bond
D
Rat-trap bond
Question 112Single Answer
I.S. code specifies that the compressive strength of brick shall be determined by keeping the brick:
1.On edge
2.On bed
3.After soaking in water for 2 hrs
4.After soaking in water for 24 hrs
A
1 and 2
B
2 and 3
C
3 and 4
D
2 and 4
Question 113Single Answer
Soundness test of cement is carried out to determine its
A
Alumina content
B
Iron oxide content
C
Free lime content
D
Durability under sea water
Question 114Single Answer
The objectives of producing cement include:
1.Incorporating industrial wastes
2.Increasing free lime
3.Increasing fineness
4.Saving energy needed in the process
A
1, 2, 3 and 4
B
1, 3 and 4 only
C
1, 2 and 4 only
D
2, 3 and 4 only
Question 115Single Answer
A mild steel rod tapers uniformly from 24 mm mm dia. over its length of 400 mm. The rod when held vertical is subjected to an axial tensile load of 12 kN. E = 2 × 105 N/mm2. The extension of the rod in mm would be:
A
3
2
B
2
3
C
3
D
1
3
Question 116Single Answer
Two different liquids are flowing through different pipes of the same diameter. In the first pipe, the flow is laminar with centerline velocity,Vmax.1,Whereas in the second pipe, the flow is turbulent. For turbulent flow, the average velocity is 0.82 times the centerline velocity,vmax.2 . For equal volumetric flow rates in both the pipes, the ratio Vmax.1/Vmax.2(up to two decimal place) is_____.
A
1.64
B
2.45
C
0.25
D
1.44
Question 117Single Answer
Poisson’s ratio of a material is 0.3. Then the ratio of Young’s modulus to bulk modulus is
A
0.6
B
0.8
C
1.2
D
1.4
Question 118Single Answer
For a gas phase cracking reaction A→B+C at 300℃ , the Gibbs free energy of the reaction at this temperature is ∆G°= -2750J/mol . The pressure is 1 bar and the gas phase can be assumed to be ideal. The universal gas constant =8.314J/mol. K. The fractional molar conversion of A at equilibrium is________.
A
0.44
B
0.50
C
0.64
D
0.80
Question 119Single Answer
Which of the following statements are correct ?
1.In a ductile material elastic deformation is more predominant than plastic one.
2.Brittleness is not an absolute property of a metal.
3.Rate of loading has no influence in changing the behavior of a metal from ‘ductile’ to ‘brittle’ at low temperatures
4.Under hydrostatic compression, a brittle metal may change into a ductile one.
A
1 and 2
B
2 and 3
C
3 and 4
D
2 and 4
Question 120Single Answer
The total deflection of a structure when subjected simultaneously to different sets of loading is equal to the sum of the deflections under each such set of loads as if acting separately on the structure. Which one the following justifies this statement?
A
Elastic limit is not exceeded
B
Elastic limit including buckling is not exceeded
C
Limit state is not exceeded
D
Proportional limit without buckling is not exceeded
Question 121Single Answer
A rectangular bar of cross-sectional area a is subjected to an axial tensile load P. The maximum shear stress will occur on a plane at X° to any normal cross-section where X° is
A
90°
B
27°
C
180°
D
45°
Question 122Single Answer
A solid circular shaft has been subjected to a pure torsion moment. The ratio of maximum shear stress to maximum normal stress at any point would be
A
1 : 2
B
1 : 1
C
2 : 3
D
2 : 1
Question 123Single Answer
Which of the following statements are correct?
1.All load carrying members transmit load through basic modes of tension, compression, torsion and shear only.
2.Beams carry transverse loads.
3.Combined loading is a complicated loading.
4.Nature of internal forces decides the aspect of combines loading.
A
1 and 2
B
2 and 3
C
3 and 4
D
2 and 4
Question 124Single Answer
Identify the WRONG statement amongst the following:
A
steam distillation is used for mixtures that re immiscible with water.
B
Vacuum distillation is used for mixtures that are miscible with water.
C
Steam distillation is used for mixtures that are miscible with water.
D
vacuum distillation columns have larger diameter as compared to atmospheric columns for the same throughout
Question 125Single Answer
Which of the following statements are correct?
1.Experimental results on thin-walled tubes show that maximum normal stress theory is valid.
2.Normal-stress theory is valid in case of brittle materials.
3.In case of pure shear, St. Venant’s theory is more valid than other theories.
4.Tresca’s theory is very closely substantiated by experimental results.
5.In maximum stress theory, the yield locus is a hexagon.
A
1, 2 and 3
B
2, 4 and 5
C
1, 2 and 4
D
2, 3 and 4
Question 126Single Answer
A thin cylindrical shell made of mild steel plate is 1000 mm in diameter. It is to be subjected to an internal pressure of 2 N/mm2. If the material yields at 200N/mm2, the thickness of the plate in mm on the basis of Rankine’s theory of failure with assuming a factor of safety of 3 would be
A
10
B
12
C
15
D
18
Question 127Single Answer
Which of the following can change if only the catalyst is changed for a reaction system?
A
Enthalpy of reaction
B
Activation energy
C
Free Energy of the reaction
D
Equilibrium constant
Question 128Single Answer
Which of the following loads should be applied on a simply supported beam, so that the shear force is constant throughout its span?
A
U.D.L. over the entire span.
B
Two concentrated loads equally spaced in the span.
C
A central concentrated load and a U.D.L. over the entires pan.
D
A couple anywhere in the span.
Question 129Single Answer
A simply supported rolled steel joist of I-section has flange width 250 mm and overall depth 600 mm. Its moment of inertia IXX = 12 × 106 mm4. The steel joist is used as a beam over a simply supported span of 6m. It carries a load of 40 kN/m including its self weight throughout the span. The maximum stress induced in the beam in N/mm2 due to bending would be
A
30
B
90
C
45
D
60
Question 130Single Answer
Which of the following terms represents the torque that produces a twist of one radian in a shaft of unit length?
A
Torsional stress
B
Torsional rigidity
C
Flexural rigidity
D
Moment of resistance
Question 131Single Answer
A 60 mm dia. shaft is subjected to a torque of 6 kN-m. C = 8 × 104 N/mm2. The maximum shear stress induced in the shaft in N/mm2will be
A
8000
92
B
4000
9
C
12000
9
D
16000
9
Question 132Single Answer
A water main 160 cm dia. contains water at a pressure head of 200m. Take weight of water to be 1000 kg/m3. The thickness of the metal shell required for the water main, given that the maximum permissible stress in the metal is 400kg/cm2, will be
A
1 cm
B
2 cm
C
3 cm
D
4 cm
Question 133Single Answer
The radial splits which are wider on the outside of the log and narrower towards the pith are known as
A
Star shakes
B
Annular rings
C
Cup shakes
D
Hear shakes
Question 134Single Answer
Consider the following distinguishing characteristics of hardwood:
1.They have distinct annular rings.
2.They are not resinous.
Which of these characteristics of hardwood is/are correct?
A
1 only
B
2 only
C
Both 1 and 2
D
Neither 1 nor 2
Question 135Single Answer
Consider the following statements on the specific gravity of wood:
1.It is always greater than 2.
2.It is less than 1.
3.It is not dependent upon temperature and equilibrium moisture content.
Which of these statements are correct?
A
1, 2, 3 and 4
B
1 and 3 only
C
2 and 3 only
D
2 and 4 only
Question 136Single Answer
The age of a log of timber can be estimated by
A
Diameter of pith
B
Thickness of bark
C
Number of annular rings
D
Number of medullary rays
Question 137Single Answer
Consider the following statements:Seasoning of timber results in
1.Increased strength
2.Increased durability
3.Reduced resilience
4.Increased dimensional stability
Which of these statements are correct?
A
1, 2 and 4
B
1, 2 and 3
C
1, 3 and 4
D
2, 3 and 4
Question 138Single Answer
Match List-I and List-II and select the correct answer using the code given below the lists: List-I List-II
Plywood 1. Furniture
Fiberboard 2. Cantilever arches
Laminated lumber 3. Insulation
Commercial blockboard 4. Lining of form-work in concrete Codes:
A
A B C D
1 2 3 4
B
4 3 2 1
C
4 2 3 1
D
4 2 3 1
Question 139Single Answer
Consider the following statements:Perforated bricks are preferred in construction since
1.They are lighter
2.They are stronger than class 1 bricks
3.They have heat-insulating properties
4.They are cheaper and need less mortar
Which of these statements are correct?
A
1, 2, 3 and 4
B
2 and 3 only
C
1 and 3 only
D
3 and 4 only
Question 140Single Answer
The standard size of a brick is
A
20 cm × 10 cm × 10 cm
B
19 cm × 9 cm × 9 cm
C
18 cm × 9 cm × 9 cm
D
18 cm × 10 cm × 10 cm
Question 141Single Answer
Consider the following statements:More than 6% magnesium oxide by weight in cement results in
1.High early strength and high heat generation
2.Less tendency towards volume change and formation of cracks
Which of these statements is/are correct?
A
1 only
B
2 only
C
Neither 1 nor 2
D
Both 1 and 2
Question 142Single Answer
Fineness if cement is measured in the units of
A
Volume/mass
B
Mass/volume
C
Area/mass
D
Mass/area
Question 143Single Answer
The initial setting time of cement depends most on
A
Tricalcium aluminate
B
Tricalciumaluminoferrite
C
Dicalcium silicate
D
Dicalcium silicate
Question 144Single Answer
Consider the following statements:Sand in cement mortar is used for
1.Increasing the strength
2.Reducing the shrinkage
3.Decreasing the surface area of the binding material
4.Decreasing the quantity of cement
Which of these statements are correct?
A
1, 2 and 4
B
1, 2 and 3
C
1, 3 and 4
D
2, 3 and 4
Question 145Single Answer
Consider the following statements:
1.The compressive strength of concrete decreases with increase in water-cement ratio of the concrete mixture.
2.Water is added to the concrete mix for hydration of cement and workability.
3.Creep and shrinkage of concrete are independent of the water-cement ratio in the concrete mix.
Which of these statements are correct?
A
1 and 4 only
B
1 and 3 only
C
2 and 3 only
D
1, 2 and 3
Question 146Single Answer
According to the Indian Standard Specifications, concrete should be cured under a humidity of
A
90%
B
80%
C
60%
D
70%
Question 147Single Answer
Consider the following statements:In a typical compression test with a cylindrical concrete specimen, failure is initiated by
1.Crushing in compression
2.Inclined shear failure
3.Longitudinal tensile cracks
Which of these statements are correct?
A
1 only
B
2 only
C
3 only
D
1, 2 and 3
Question 148Single Answer
If one intends to obtain the best workability of concrete, the preferred shape of aggregate is
A
Round
B
Annular
C
Triangular
D
Flinty
Question 149Single Answer
Consider the following statements as regards rheology of concrete:
1.It deals with strength of concrete.
2.It deals with deformation in concrete.
3.It is the study of deformation and flow of concrete.
4.It deals with rate of shear and shear stress in concrete.
Which of these statements are correct?
A
1, 2, 3 and 4
B
3 and 4 only
C
2 and 3 only
D
1 and 2 only
Question 150Single Answer
Consider the following for durability of well-graded concrete:
1.The environment
2.Cover to embedded reinforcement
3.Shape and size of concrete member
Which of these are correct?