📚 Exam by Category
▾
Objective Questions

Latest SAMEER Project Engineer Exam Question (Objective Questions), MCQ in English

Subjects : Concerned Subject (Electronics)

Question Bank SAMEER Project Engineer Exam (Electronics Engineering) - English
Back to Exam

Concerned Subject (Electronics)

Question 1Single Answer
Which one of the following helps experimental confirmation of the Crystalline state of matter?
  1. A
    Shock compression
  2. B
    Photo emission
  3. C
    Conductivity measurements
  4. D
    X-ray diffraction
Question 2Single Answer
Which of the following regions of operation are mainly responsible for heating of the transistor under switching operation?
1. Saturation region
2. Cut-off region
3. Transition from saturation to cut-off
4. Transition from cut-off to saturation
Select the correct answer using the codes given below
  1. A
    1, 2 and 4 only
  2. B
    1, 3 and 4 only
  3. C
    2 and 3 only
  4. D
    1 and 3 only
Question 3Single Answer
In a sinusoidal oscillator, sustained oscillations will be produced only if the loop gain (at the oscillation frequency) is
  1. A
    Less than unity but not zero
  2. B
    Zero
  3. C
    Unity
  4. D
    Greater than unity
Question 4Single Answer
Consider the following statements:
The output of a linear circuit, driven with a sine wave at a frequency f, is itself a sine wave
1. at the same frequency
2. with chance of changed amplitude
3. with chances of changed amplitude and phase
Which of the above statements is/are correct? 
  1. A
    1 and 2
  2. B
    1 only
  3. C
    1 and 3
  4. D
    2 only 
Question 5Single Answer
Consider the following statements:
The main contribution to photo conduction is by
1. the generation of electron and hole pair by a photon
2. a donor electron jumping into the conduction band because of a photon’s energy
3. a valence electron jumping into an acceptor state because of a photon’s energy Which of the above statements is/are correct? 
  1. A
    1 only
  2. B
    2 only
  3. C
    3 only
  4. D
    1, 2 and 3
Question 6Single Answer
At temperature of 298 Kelvin, Silicon is not suitable for most-electronic applications, due to small amount of conductivity. This can be altered by
  1. A
    Gettering
  2. B
    Doping
  3. C
    Squeezing
  4. D
    Sintering
Question 7Single Answer
By doping Germanium with Gallium, the types of semi-conductors formed are
1. N type
2. P type
3. Intrinsic
4. Extrinsic
  1. A
    1 and 4
  2. B
    2 and 4
  3. C
    1 and 3
  4. D
    2 and 3
Question 8Single Answer
An n-type of silicon can be formed by adding impurity of:
1. Phosphorous
2. Arsenic
3. Boron
4. Aluminum 
Which of the above are correct ?
  1. A
    1 and 2
  2. B
    2 and 3
  3. C
    3 and 4
  4. D
    1 and 4
Question 9Single Answer
According to Einstein’s relationship for a semiconductor, the ratio of diffusion constant to the mobility of the charge carriers is
  1. A
    Variable and is twice the volt equivalent of the temperature
  2. B
    Constant and is equal to the volt equivalent of the temperature
  3. C
    Equal to two and is twice the volt equivalent of the temperature
  4. D
    Equal to one and is equal to the volt equivalent of the temperature
Question 10Single Answer
Swept-out voltage in PIN diode happens when PIN diode is
  1. A
    Forward biased and the thickness of the depletion layer decreases till I-region becomes free of mobile carriers
  2. B
    Reverse biased and the thickness of the depletion layer increases till I-region becomes free of mobile carriers
  3. C
    Forward biased and the thickness of the depletion layer increases till I-region becomes free of mobile carriers
  4. D
    Reverse biased and the thickness of the depletion layer decreases till I-region becomes free of mobile carriers
Question 11Single Answer
The number of holes in an N-type silicon with intrinsic value 1.5 × 1010/cm3 and doping concentration of 1017/cm3, by using mass-action law is
  1. A
    6.67 × 106/cc
  2. B
    4.44 × 10-25/cc
  3. C
    1.5× 10-24/cc
  4. D
    2.25 × 103/cc
Question 12Single Answer
A tunnel-diode is best suited for
  1. A
    Very low frequencies
  2. B
    50 Hz
  3. C
    100 Hz
  4. D
    Microwave frequencies
Question 13Single Answer
Small recovery time of a diode is most significant for
  1. A
    Line-frequency rectification
  2. B
    Switching operations
  3. C
    High-frequency rectifications and switching operations
  4. D
    Low-frequency rectifications and switching operations
Question 14Single Answer
In JFET, when operated above the pinch-off voltage, the
  1. A
    Depletion region becomes smaller
  2. B
    Drain current starts decreasing
  3. C
    Drain current remains practically constant
  4. D
    Drain current increases steeply
Question 15Single Answer
Thermal runaway is not possible in FET because, as the temperature of FET increases
  1. A
    The drain current increases
  2. B
    The mobility of charge carriers decreases
  3. C
    The mobility of charge carriers increases
  4. D
    The transconductance increases
Question 16Single Answer
Consider the following statements regarding an N-P-N Bipolar Junction Transistor:
1. Emitter diode is forward biased and collector diode is reverse biased
2. Emitter has many free electrons
3. Free electrons are injected into base and pass through collector
4. Depletion layers around junction J1 and J2 of BJT are widened 
    Which of the above statements are correct?
  1. A
    1, 2 and 4
  2. B
    1, 3 and 4
  3. C
    2, 3 and 4
  4. D
    1, 2 and 3
Question 17Single Answer
A freewheeling diode T phase controlled rectifier
  1. A
    Improves the line power factor
  2. B
    Enables inverse operation
  3. C
    Is responsible for additional reactive power
  4. D
    Is responsible for additional harmonics
Question 18Single Answer
The zeners incorporated within the encapsulations of some MOSFETs are meant for
  1. A
    Reducing the cost
  2. B
    Biasing the gate circuit
  3. C
    Self-protecting the device against transients
  4. D
    None of the above
Question 19Single Answer
When UJT is used for triggering an SCR, the wave-shape of the signal obtained from UJT circuit is
  1. A
    Sine wave
  2. B
    Saw tooth wave
  3. C
    Trapezoidal wave
  4. D
    Square wave
Question 20Single Answer
Darlington pairs are frequently used in linear ICs because, they
  1. A
    Do not require any capacitors or inductors
  2. B
    Have enormous impedance transformation capability
  3. C
    Can be readily formed/hooked from two adjacent transistors
  4. D
    Resemble emitter follower
Question 21Single Answer
In intrinsic semiconductors, the Fermi level lies?
  1. A
    At mid-gap
  2. B
    Near valence band
  3. C
    Near conduction band
  4. D
    Outside the band gap
Question 22Single Answer
Which material is a direct band-gap semiconductor?
  1. A
    Gallium Arsenide
  2. B
    Germanium
  3. C
    Silicon
  4. D
    Tin
Question 23Single Answer
Indirect band-gap semiconductors require phonon interaction because?
  1. A
    Charge neutrality
  2. B
    Energy conservation
  3. C
    Momentum conservation
  4. D
    Thermal equilibrium
Question 24Single Answer
Band gap of silicon at room temperature is approximately?
  1. A
    0.66 eV
  2. B
    0.72 eV
  3. C
    1.43 eV
  4. D
    1.12 eV
Question 25Single Answer
Increase in temperature causes band gap of semiconductor to?
  1. A
    Increase
  2. B
    Decrease
  3. C
    Remain constant
  4. D
    Become zero
Question 26Single Answer
Electrical conductivity of intrinsic semiconductor depends mainly on?
  1. A
    Doping
  2. B
    Crystal size
  3. C
    Mobility only
  4. D
    Temperature
Question 27Single Answer
In n-type semiconductor, majority carriers are?
  1. A
    Holes
  2. B
    Excitons
  3. C
    Ions
  4. D
    Electrons
Question 28Single Answer
Density of states in conduction band increases with?
  1. A
    Decrease in energy
  2. B
    Cube of energy
  3. C
    Square root of energy
  4. D
    Linear energy
Question 29Single Answer
Fermi level shifts towards conduction band in?
  1. A
    p-type material
  2. B
    Intrinsic material
  3. C
    n-type material
  4. D
    Insulator
Question 30Single Answer
Semiconductor becomes degenerate when?
  1. A
    Lightly doped
  2. B
    Undoped
  3. C
    Heavily doped
  4. D
    Heated
Question 31Single Answer
Gradient of a scalar field gives a?
  1. A
    Vector
  2. B
    Scalar
  3. C
    Tensor
  4. D
    Constant
Question 32Single Answer
Divergence of a vector field physically represents?
  1. A
    Source or sink strength
  2. B
    Flux density
  3. C
    Curling tendency
  4. D
    Energy density
Question 33Single Answer
Curl of a vector field indicates?
  1. A
    Rotational tendency
  2. B
    Rate of change
  3. C
    Flux
  4. D
    Potential
Question 34Single Answer
Divergence of curl of any vector field is always?
  1. A
    Zero
  2. B
    Maximum
  3. C
    Unity
  4. D
    Infinite
Question 35Single Answer
Curl of gradient of any scalar field is always?
  1. A
    Unity
  2. B
    Zero
  3. C
    Infinite
  4. D
    Maximum
Question 36Single Answer
Del operator is used to represent?
  1. A
    Scalar multiplication
  2. B
    Vector differentiation
  3. C
    Integration
  4. D
    Transformation
Question 37Single Answer
Line integral of electric field around closed path equals?
  1. A
    Zero in electrostatics
  2. B
    Magnetic flux
  3. C
    Charge density
  4. D
    Current
Question 38Single Answer
Volume integral of divergence of vector equals?
  1. A
    Surface integral of normal component
  2. B
    Line integral
  3. C
    Curl integral
  4. D
    Zero
Question 39Single Answer
Gauss divergence theorem relates?
  1. A
    Line and surface integrals
  2. B
    Surface and volume integrals
  3. C
    Line and volume integrals
  4. D
    Curl and gradient
Question 40Single Answer
Stokes theorem relates?
  1. A
    Surface integral of divergence
  2. B
    Line integral of curl
  3. C
    Volume integral of gradient
  4. D
    Surface integral of curl to line integral
Question 41Single Answer
The determinant of an identity matrix of any order is:
  1. A
    1
  2. B
    0
  3. C
    −1
  4. D
    Depends on order
Question 42Single Answer
The eigenvalues of a triangular matrix are its:
  1. A
    Row sums
  2. B
    Column sums
  3. C
    Determinants
  4. D
    Diagonal elements
Question 43Single Answer
If A is an orthogonal matrix, then:
  1. A
    A² = 0
  2. B
    AᵀA = I
  3. C
    Aᵀ = 0
  4. D
    det(
Question 44Single Answer
The trace of a matrix is the sum of its:
  1. A
    Eigenvectors
  2. B
    Rows
  3. C
    Diagonal elements
  4. D
    Columns
Question 45Single Answer
The inverse of a matrix exists only when the matrix is:
  1. A
    Non-singular
  2. B
    Singular
  3. C
    Rectangular
  4. D
    Zero
Question 46Single Answer
For a symmetric matrix A:
  1. A
    Aᵀ = −A
  2. B
    det(
  3. C
    A² = I
  4. D
    Aᵀ = A
Question 47Single Answer
The rank of an n × n identity matrix is:
  1. A
    0
  2. B
    n
  3. C
    1
  4. D
    n − 1
Question 48Single Answer
If λ is an eigenvalue of A, then an eigenvalue of A² is:
  1. A
    λ
  2. B
    2λ
  3. C
    √λ
  4. D
    λ²
Question 49Single Answer
A matrix whose transpose is equal to its negative is called:
  1. A
    Symmetric
  2. B
    Skew-symmetric
  3. C
    Orthogonal
  4. D
    Hermitian
Question 50Single Answer
The diagonal elements of a real skew-symmetric matrix are:
  1. A
    1
  2. B
    0
  3. C
    −1
  4. D
    Arbitrary
Important Questions Package

SAMEER Project Engineer Exam Online Question Bank Package

Buy SAMEER Project Engineer Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in SAMEER Project Engineer question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.SAMEER Project Engineer Exam (Electronics Engineering) - English
Description : 1000 Question with Answer
₹101 [₹500]
2.SAMEER Project Engineer Exam (Electronics Engineering) - English
Description : 2000 Question with Answer
₹151 [₹500]
3.SAMEER Project Engineer Exam (Electronics Engineering) - English
Description : 3000 Question with Answer
₹181 [₹500]
4.SAMEER Project Engineer Exam (Electronics Engineering) - English
Description : 4000 Question with Answer
₹201 [₹500]
5.SAMEER Project Engineer Exam (Mechanical Engineering) - English
Description : 1000 Question with Answer
₹101 [₹500]
6.SAMEER Project Engineer Exam (Mechanical Engineering) - English
Description : 2000 Question with Answer
₹151 [₹500]
7.SAMEER Project Engineer Exam (Mechanical Engineering) - English
Description : 3000 Question with Answer
₹181 [₹500]
8.SAMEER Project Engineer Exam (Mechanical Engineering) - English
Description : 4000 Question with Answer
₹201 [₹500]
9.SAMEER Project Engineer Exam (Electronics Engineering) - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹550]
10.SAMEER Project Engineer Exam (Mechanical Engineering) - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
11.SAMEER Project Engineer Exam (Electronics Engineering) Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹600]
12.SAMEER Project Engineer Exam (Mechanical Engineering) Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹600]
13.SAMEER Project Engineer Exam (Electronics Engineering) - English (Old)
Description : 1000 Question With Answer
₹101 [₹500]
Back to Exam
Question for SAMEER Project Engineer 2026 - Quiz / Questions / MCQ - Toppersexam