The payment was collected by the hardworking salesman.
A
The hardworking salesman collected the payment.
B
the salesman who worked heard was able to collect the payment.
C
to collect the payment the salesman had to work hard.
D
The hardworking salesman was able to collect the payment.
Question 4Single Answer
I had to stop all my work to complete this project.
A
All other work had to be stopped to complete this project by me
B
For completing this project all other work must be stopped
C
For completing this project I had to stop all my work
D
To complete this project all other work had been stopped by me
Question 5Single Answer
They have published the names of all the successful candidates.
A
The candidates who have succeeded their names they had published.
B
The names of all the successful candidates have been published by them
C
The candidates who have succeeded their names have been published by them.
D
The names of all the successful candidate were published by them.
Question 6Single Answer
The online shopping site lowered the prices.
A
Lowering of the prices was done by the online shopping site
B
The prices were lowered by the online shopping site
C
The prices had been lowered by the online shopping site
D
The prices have been lowered by the online shopping site
Question 7Single Answer
Who taught you to drive a truck ?
A
To drive a truck by whom were you taught?
B
Driving a truck by who were you taught?
C
Driving a truck by who were you being taught?
D
By whom were you taught to drive a truck?
Question 8Single Answer
We shall invite Suresh.
A
Suresh would be invited by us
B
Suresh would have been invited by us
C
Suresh will be invited by us
D
Suresh will have been invited by us
Question 9Single Answer
Dark clouds have overcast the evening sky.
A
By the dark clouds the evening sky was overcast.
B
The evening sky has been overcast by the dark clouds.
C
Dark clouds overcastted the evening sky.
D
The sky of the evening was overcasted by dark clouds.
Question 10Single Answer
The partners will celebrate their triumph tomorrow.
A
The triumph would be celebrated by the partners a day before
B
The triumph would be celebrated by the partners a day after
C
The triumph would have been celebrated by the partners a day after
D
The triumph will have been celebrated by the partners tomorrow
Question 11Single Answer
Why did break the vase?
A
why is the vase broken by him
B
why was the vase broken by him
C
why had been the vase broken by him
D
why has been the vase broken by him
Question 12Single Answer
Mariam was writing a note to her boss.
A
A note was written to her boss by Mariam
B
A note was wrote by Mariam to her boss
C
A note was being written by Mariam to her boss
D
A note was written by Mariam to her boss
Question 13Single Answer
The baby really enjoys that music.
A
That music was really enjoyed by the baby.
B
That music was really being enjoyed by the baby.
C
That music is really enjoyed by the baby.
D
This music was really enjoyed by the baby.
Question 14Single Answer
The weather disrupted the final match.
A
The final match has been disrupted by the weather.
B
The final match had been disrupted by the weather.
C
The final match was disrupted by the weather.
D
The final match was being disrupted by the weather.
Question 15Single Answer
The management committee is required to publish a report every year.
A
report would be published by the management committee every year.
B
A report would have been published by the management committee every year.
C
A report requires to be published by the management committee every year.
D
Every year the report would be published by the management committee.
Question 16Single Answer
Passage :
Direction : Question below has two blanks, each blank indicting that some thing has been omitted. Choose the word for each blank which best fits the meaning of the sentence as a whole.
The Finance Department has ……………a centralized online databank system for all statutory government bodies to …………an eye on their assets and liabilities.
A
presented , stay
B
introduced , keep
C
announce , make
D
created , let
E
proclaimed , hold
Question 17Single Answer
Passage :
Direction : The five items in this section consists of a word or group of words followed by four words as (a), (b), (c) and (d). Select the word which is nearly opposite to the meaning of the original word or group of words and mark your response as (a), (b), (c) and (d), as the case may be, in your Answer Sheet.
Assets
A
liabilities
B
responsibilities
C
estates
D
profits
Question 18Single Answer
Passage :
Direction : In the question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it
Affidavit
A
Affirmation
B
Slander
C
Oath
D
Testimony
Question 19Single Answer
Passage :
Direction: In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it
Hollow
A
Alveolate
B
Cleft
C
Cavernous
D
Solid
Question 20Single Answer
Passage :
Directions: In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it
Cosset
A
Ignoreb
B
Close
C
Caress
D
Fondle
Question 21Single Answer
Passage :
Directions: In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it
Ogle
A
Leer
B
Gaze
C
Ignore
D
Gawk
Question 22Single Answer
Passage :
Directions:In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it
Intrinsic
A
Elemental
B
Innate
C
Connate
D
Acquired
Question 23Single Answer
Passage :
Direction : In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it
Coalesce
A
Separate
B
Adhere
C
Cleave
D
Amalgamate
Question 24Single Answer
Passage :
Directions: In the following question, out of the four alternatives, choose the word which is opposite in meaning to the given word and click the button corresponding to it
Loiter
A
lag
B
Hasten
C
Amble
D
Loii
Question 25Single Answer
Passage :
Direction : Question below has two blanks, blank indicating that something has been omitted. Choose the set of words for blank which best fits the meaning of the sentence as a whole.
The protests were......... at ......... awareness among the elite and the educated.
A
held, generating
B
aimed, creating
C
targeted, awakening
D
focused, building
E
concentrated, producing
Reasoning
Question 26Single Answer
Passage :
Direction : the sets of numbers in the four alternatives given below, which is the most similar to the given set.
Given Set : (6, 15, 28)
A
(50,59,71)
B
(46, 56, 66)
C
(60, 69, 72)
D
(60, 69, 82)
E
None of these
Question 27Single Answer
Passage :
Direction : the sets of numbers in the four alternatives given below, which is the most similar to the given set.
Given Set : (81, 77, 69)
A
(56, 52, 44)
B
(64, 61, 53)
C
(92, 88, 79)
D
(75, 71, 60)
E
None of these
Question 28Single Answer
Passage :
Direction : The questions consists of a pair of words. Establish the relationship among the given pair and identify the pair that best illustrates a similar relationship from amongst the alternatives
Kick : Football
A
Mop : Sweep
B
Dust : Rage
C
Wash : Dishes
D
Throw : Ring
E
None of these
Question 29Single Answer
Passage :
Direction : The questions consists of a pair of words. Establish the relationship among the given pair and identify the pair that best illustrates a similar relationship from amongst the alternatives
Rectangle : Pentagon
A
Triangle : Rectangle
B
Diagonal : Perimeter
C
Side : Angle
D
Circle : Square
E
None of the above
Question 30Single Answer
Passage :
Direction : The questions consists of a pair of words. Establish the relationship among the given pair and identify the pair that best illustrates a similar relationship from amongst the alternatives
Inherit : Acquire
A
Instinct : Habbit
B
Learn : Discover
C
Loss : Gain
D
Hierarchical : Succession
E
None of the above
Question 31Single Answer
Passage :
Direction: The questions consists of a pair of words bearing a certain relationship. From amongst the alternatives, pick up the pair that best illustrates a similar relationship.
Court : Justic
A
Police : Crime
B
Teacher : Study
C
Doctor : Sickness
D
Auditor : Accuracy
E
None of these
Question 32Single Answer
Passage :
Direction: The questions consists of a pair of words bearing a certain relationship. From amongst the alternatives, pick up the pair that best illustrates a similar relationship.
Coal : Thermal
A
Power : Energy
B
Bulb : Light
C
Air : Atmosphere
D
Water : Hydel
E
None of the above
Question 33Single Answer
Passage :
Direction : In these question, relationship between different elements is shown in the statements.The statements are followed by conclusions. Study the conclusions based on the given statements and select the appropriate answer
Statements I=H>C> N < E=S Conclusions
I. I > H
II. C > S
A
Neither conclusion I nor conclusion II is true
B
Either conclusion I or II is true
C
Only conclusion II is true
D
Only conclusion I is true
E
Both conclusions I and II are true
Question 34Single Answer
Passage :
Direction : In these question, relationship between different elements is shown in the statements.The statements are followed by conclusions. Study the conclusions based on the given statements and select the appropriate answer
Statements G> R>E=A<T<S:D<A<J Conclusions
I. T D
II. R > S
A
Only conclusion II is true
B
Only conclusion I is true
C
Both conclusions I and II are true
D
Either conclusion I or II is true
E
Neither conclusion I nor II is true
Question 35Single Answer
Passage :
Direction : In these question, relationship between different elements is shown in the statements.The statements are followed by conclusions. Study the conclusions based on the given statements and select the appropriate answer
Statements G>R> E=A<T<S:D<A<J Conclusions
I J > G
II. J = G
A
Only conclusion II is true
B
Only conclusion I is true
C
Both conclusions I and II are true
D
Either conclusion I or II is true
E
Neither conclusion I nor II is true
Question 36Single Answer
Passage :
Direction : In these question, relationship between different elements is shown in the statements. The statements are followed by conclusions. Study the conclusions based on the given statements and select the appropriate answer
Statements S< L< I = P E> R : L > Q Conclusion
I. L> R
II.E> Q
A
Only conclusion II is true
B
Only conclusion I is true
C
Both conclusions I and II are true
D
Either conclusion I or II is true
E
Neither conclusion I nor II is true
Question 37Single Answer
Passage :
Direction : In these question, relationship between different elements is shown in the statements. The statements are followed by conclusions. Study the conclusions based on the given statements and select the appropriate answer
Statements C > W > E=R < B < S: H< R >D Conculsions
I. C > D
II.H < S
A
Either conclusion I or II is true
B
Only conclusion I is true
C
Both conclusions I and II are true
D
Neither conclusion I nor II is true
E
Only conclusion II is true
Question 38Single Answer
Passage :
DirectionIn these questions, relationship between different elements is shown in the statements. The statements are followed by conclusions. Study the conclusions based on the given statements and select the appropriate answer
Statements V= D < Y < A > G> E :P= R : A < V Conclusions
I. E > P
II. P > E
A
Either conclusion I or II is true
B
Only conclusion I is true
C
Both conclusions I and II are true
D
Neither conclusion I nor II is true
E
Only conclusion II is true
Question 39Single Answer
Passage :
Directions : In these questions, relationship between different elements is shown in the statements. The statements are followed by conclusions. Study the conclusions based on the given statements and select the appropriate answer
Statements S>J =T< O :T< P Conculsions
I. S O
II. P < S
A
Either conclusion I or II is true
B
Only conclusion I is true
C
Both conclusions I and II are true
D
Neither conclusion I nor II is true
E
Only conclusion II is true
Question 40Single Answer
Passage :
Directions : In these questions, relationship between different elements is shown in the statements. The statements are followed by conclusions. Study the conclusions based on the given statements and select the appropriate answer
A
Either conclusion I or II is true
B
Only conclusion I is true
C
Both conclusions I and II are true
D
Neither conclusion I nor II is true
E
Only conclusion II is true
Civil
Question 41Single Answer
One bag of Portland cement, 50 kg in weight, would normally have a bulk volume of
A
30 l
B
35 l
C
40 l
D
45 l
Question 42Single Answer
AsCu, a preservative for wood, developed by the Forest Research Institute, Dehradun, comprises of chemicals:
A
1 : 1 : 1
B
1 : 2 : 3
C
1 : 2 : 4
D
1 : 3 : 4
Question 43Single Answer
Consider the following statements related to autoclave bricks:
1.Less water absorption compared to other bricks.
2.Noise reduction
3.It is cheap compared to other types of bricks.
4.Requirement of bulk volume of mortar in joints being relatively less compared to other types of brick masonry.
5.Not recommended for outer walls.
Which of the above statements are relevant to the use of ‘autoclave’ bricks?
A
1, 2 and 4
B
1, 3 and 5
C
2, 3 and 4
D
2, 4 and 5
Question 44Single Answer
The minimum number of annular rings to be seen in every 2.54 cm in the radial direction from the core for timber to be classified as ‘Dense’ is
A
10
B
20
C
25
D
30
Question 45Single Answer
If the actual thickness of a brick masonry wall is 19 cm, its effective length is 2.70 m, its effective height is 2.82 m and its code specified stiffening coefficient is 1.2 then, for design considerations, the slenderness ratio of the wall will be taken as
A
11.8
B
12.4
C
14.2
D
14.8
Question 46Single Answer
Consider the following forms of water in a hydrated cement paste:
1.Capillary water
2.Chemically combined water
3.Interlayer water
4.Adsorbed water
Which of the above forms of water will, on its/their removal, cause shrinkage of the paste?
A
1, 2 and 3
B
1, 2 and 4
C
2, 3 and 4
D
1, 3 and 4
Question 47Single Answer
Consider the following statements:High early strength of cement is obtained as a result of
1.Fine grinding.
2.Decreasing the lime content
3.Burning at higher temperature
4.Increasing the quality of gypsum.
Which of the above statements are correct?
A
1 and 2
B
1 and 3
C
2 and 3
D
3 and 4
Question 48Single Answer
Consider the following statements related to ‘composite mortar’:
1.Addition of lime to cement mortar improves its workability
2.Composite mortar is obtained by adding 10% by weight of cement and mixing with water.
3.Composite mortar is not preferred in tall buildings.
4.Mechanical grinding is essential for developing composite mortar.Which of the above statements are true in this case?
A
1, 2 and 3 only
B
1, 3 and 4 only
C
2, 3 and 4 only
D
1, 2, 3 and 4
Question 49Single Answer
Consider the following statements related to ‘non-destructive testing’ of concrete:
1.Indentation test is used to assess the quality of concrete.
2.Resonant Frequency Method is based on a laboratory test.
3.Compressive strength of concrete is estimated through Pulse Velocity Measurement.
4.Dynamic modulus of Elasticity is determined by a Sonometer Test.
5.Thickness of concrete can be estimated by in-situ Rebound Hammer Test.
Which of the above statements are correct?
A
1, 2 and 3 only
B
1, 2 and 5 only
C
1, 2, 3 and 4 only
D
1, 2, 3, 4 and 5
Question 50Single Answer
What is the amount of water required for a workable RC of mix 1 : 2: 4 by weight., when W/C is 0-60 and unit weight of concrete is 2400 kg/m3?
A
165 l
B
205 l
C
245 l
D
285 l
Important Questions Package
NAL Technical Assistant Exam Online Question Bank Package
Buy NAL Technical Assistant Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in NAL Technical Assistant question bank 2026 in Online, PDF & Print study material.
+ Free Monthly Current Affairs, GK & more PDF Download
Sr.
Package Name
Amount
1.
NAL Technical Assistant Exam (Civil) - English
Description : 2000 Question with Answer
₹181[₹500]
2.
NAL Technical Assistant Exam (Civil) - Hindi
Description : 2000 Question with Answer
₹181[₹500]
3.
NAL Technical Assistant Exam (Electrical) - English
Description : 2000 Question with Answer
₹181[₹500]
4.
NAL Technical Assistant Exam (Electrical) - Hindi
Description : 2000 Question with Answer
₹181[₹500]
5.
NAL Technical Assistant Exam (Civil) Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390[₹600]
6.
NAL Technical Assistant Exam (Civil) Question Bank Book - Hindi
Description : 1000 Question with Answer (Printed Material)
₹450[₹800]
7.
NAL Technical Assistant Exam (Electrical) Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390[₹600]
8.
NAL Technical Assistant Exam (Electrical) Question Bank Book - Hindi
Description : 1000 Question with Answer (Printed Material)
₹450[₹800]
Civil
Question 51Single Answer
Which IS code is used for classification of timber for seasoning purposes?
A
IS : 4970-1973
B
IS : 1708-1969
C
IS : 1141-1958
D
IS : 399-1963
Question 52Single Answer
Consider the following with regard to the application of preservation of timber:
1.Increase in the life span of the member
2.Increase in the strength of the timber
3.Removal of moisture
4.Prevention of growth of fungi by killing them
Which of the above are correct?
A
1, 2, 3 and 4
B
2 and 4 only
C
1 and 4 only
D
2 and 3 only
Question 53Single Answer
The plies in plywood are so placed that the grains of each ply are
A
Parallel to each other
B
At right angle to one another
C
45° oblique to adjacent grain
D
Not constrained by any consideration
Question 54Single Answer
Which of the following is an ODD one as regards ‘requirement of good brick-earth’?
A
It must be free from lumps of lime
B
It should not be mixed with salty water
C
It must be non-homogeneous
D
It should not contain vegetable and organic matter
Question 55Single Answer
The compressive strength of heavy-duty bricks, as per IS : 2980-1962, should not be less than
A
440 kg/cm2
B
175 kg/cm2
C
100kg/cm2
D
75kg/cm2
Question 56Single Answer
Consider the following statements:
1.Brickwork will have high water tightness.
2.Brickwork is preferred for monument structures.
3.Bricks resist fire better than stones
4.Bricks of good quality shall have thin mortar bonds.
Which of the above statements are correct?
A
1 and 2
B
3 and 4
C
2 and 3
D
1 and 4
Question 57Single Answer
Consider the following statements:A good soil for making bricks should contain
1.30% alumina
2.10% lime nodules
3.Only small quantity of iron oxides
4.15% magnesia
Which of the above statements are correct?
A
1 and 2 only
B
1 and 3
C
1, 2 and 4
D
2, 3 and 4
Question 58Single Answer
Which compound of cement is responsible for strength of cement?
A
Magnesium oxide
B
Silica
C
Alumina
D
Calcium sulphate
Question 59Single Answer
Which type of cement is recommended in large mass concrete works such as a dam?
A
Ordinary Portland
B
High Alumina
C
Low-heat Portland
D
Portland Cement
Question 60Single Answer
Consider the following statements regarding ‘setting of cement’:
1.Low-heat cement sets faster than OPC.
2.Final setting time decides the strength of cement
3.Initial setting time of Portland Pozzollona is 30 minutes
4.Air-induced setting is observed when stored under damp conditions.
4.Addition of gypsum retards the setting time.
Which of the above statements are correct?
A
1, 2 and 3
B
2, 3 and 4
C
3, 4 and 5
D
2, 3 and 5
Question 61Single Answer
Consider the following statements regarding ‘strength of cement’:
1.Strength test on cement is made on cubes of cement-sand mix.
2.Water to be used for the paste is 0.25 P, where P is the water needed for normal consistency.
3.The normal consistency is determined on Le Chatelier’s principle.
4.Cubes are cast in two layers in leak-proof moulds further compacted in each layer by vibration on a machine.
Which of the above statements are correct?
A
1 and 2
B
2 and 3
C
1 and 4
D
3 and 4
Question 62Single Answer
Which of the following ingredients refer to binding material of mortar?
1.Cement
2.Lime
3.Sand
4.Ashes
Select the correct answer using the code given below.
A
1 and 4
B
3 and 4
C
1 and 2
D
2 and 3
Question 63Single Answer
Consider the following statements:
1.Bricks in masonry are bound by mortar.
2.Mortars make brick damp-proof.
3.Strength of brick in masonry is improved by plastering.
4.Addition of lime improves workability.
5.Marine construction needs sulphate-resistant cement mortar.
Which of the above statements are relevant for ‘cement mortar’?
A
1, 2 and 3
B
2, 3 and 4
C
1, 4 and 5
D
3, 4 and 5
Question 64Single Answer
Consider the following parameters of concrete:
1.Impermeability
2.Compactness
3.Durability
4.Desired consistency
5.Workability
Which of the above parameters are relevant for ‘water-cement ratio’?
A
4 and 5
B
1 and 2
C
2 and 4
D
3 and 5
Question 65Single Answer
Consider the following statements:Presence of Na2O and K2O in concrete leads to
1.Expansive reaction in concrete
2.Cracking of concrete
3.Disruption of concrete
4.Shrinkage of concrete
Which of the above statements are correct?
A
1 and 2 only
B
2 and 3 only
C
1, 2 and 3
D
3 and 4
Question 66Single Answer
The maximum total quantity of dry aggregate by mass per 50 kg of cement, to be taken as the sum of the individual masses of fine and coarse aggregates (kg), for M20 grade of concrete is
A
625
B
480
C
330
D
250
Question 67Single Answer
Absorption capacity of an aggregate refers to the difference expresses in appropriate proportion in water content between
A
A wet aggregate and a dry aggregate
B
A dry aggregate and a wet aggregate
C
A saturated surface-dry aggregate and a dry aggregate
D
A saturated surface-dry aggregate and an over dry aggregate
Question 68Single Answer
Consider the following statements concerning ‘elasticity of concrete’:
1.Stress-strain behavior of concrete is a straight line up to 10% ultimate stress.
2.Strain determination is obtained from tangent modulus.
3.Modulus of elasticity of concrete is also called as secant modulus.
Which of the above statements are correct?
A
1, 2 and 3
B
1 and 3 only
C
1 and 2 only
D
2 and 3 only
Question 69Single Answer
Consider the following statements :The addition of CaCl2 in concrete results in
1.Increased shrinkage
2.Decreased setting time
3.Decreased shrinkage
4.Increased setting time
Which of the above statements are correct?
A
1 only
B
2 and 3
C
3 and 4
D
1 and 2
Question 70Single Answer
Which of the following statements are correct ?
1.Knots in a tree affect the continuity of fibres.
2.Nail knots do not influence the strength of timber.
3.Druxiness of wood is not a defect.
4.Tall trees with twisted fibers give good timber for poles.
A
1, 2, 3 and 4
B
1, 2 and 4 only
C
1, 2 and 3 only
D
2, 3 and 4 only
Question 71Single Answer
Excrescences in wood are
1.Defects found in trees
2.Formed due to injuries inflicted on trees when they are growing
3.Defects which render wood suitable as firewood only
A
1, 2 and 3
B
1 and 2 only
C
1 and 3 only
D
2 and 3 only
Question 72Single Answer
What treatment is adopted for making timber fire-resistant?
A
ASCU treatment
B
Abel’s process
C
Creosoting
D
Tarring
Question 73Single Answer
Deterioration of structure of timber due to dry rot is:
1.Caused by fungi
2.Due to dry-spell after heavy rains
3.Due to attack of termites
4.ndicated by surface stripes on scantlings
A
1 and 2
B
3 and 4
C
2 and 3
D
1 and 4
Question 74Single Answer
Alternate wetting and drying of timber :
1.Results in shrinkage and swelling
2.Brings about wet rot onset
3.Increases the durability
4.Causes transmission of spores from germination
A
1, 2, 3 and 4
B
1, 2 and 4 only
C
1, 2 and 3 only
D
2, 3 and 4 only
Question 75Single Answer
As per I.S. classification, the minimum compressive strength of a first class brick should be
A
75 kg/cm3
B
100kg/cm3
C
125 kg/cm3
D
150 kg/cm3
Question 76Single Answer
When provided with alternating courses of (a) all headers and (b) all stretchers, the front elevation of such brick masonry is designated as
A
English bond
B
Single Flemish bond
C
Double Flemish bond
D
Rat-trap bond
Question 77Single Answer
I.S. code specifies that the compressive strength of brick shall be determined by keeping the brick:
1.On edge
2.On bed
3.After soaking in water for 2 hrs
4.After soaking in water for 24 hrs
A
1 and 2
B
2 and 3
C
3 and 4
D
2 and 4
Question 78Single Answer
Soundness test of cement is carried out to determine its
A
Alumina content
B
Iron oxide content
C
Free lime content
D
Durability under sea water
Question 79Single Answer
The objectives of producing cement include:
1.Incorporating industrial wastes
2.Increasing free lime
3.Increasing fineness
4.Saving energy needed in the process
A
1, 2, 3 and 4
B
1, 3 and 4 only
C
1, 2 and 4 only
D
2, 3 and 4 only
Question 80Single Answer
A mild steel rod tapers uniformly from 24 mm mm dia. over its length of 400 mm. The rod when held vertical is subjected to an axial tensile load of 12 kN. E = 2 × 105 N/mm2. The extension of the rod in mm would be:
A
3
2
B
2
3
C
3
D
1
3
Question 81Single Answer
Two different liquids are flowing through different pipes of the same diameter. In the first pipe, the flow is laminar with centerline velocity,Vmax.1,Whereas in the second pipe, the flow is turbulent. For turbulent flow, the average velocity is 0.82 times the centerline velocity,vmax.2 . For equal volumetric flow rates in both the pipes, the ratio Vmax.1/Vmax.2(up to two decimal place) is_____.
A
1.64
B
2.45
C
0.25
D
1.44
Question 82Single Answer
Poisson’s ratio of a material is 0.3. Then the ratio of Young’s modulus to bulk modulus is
A
0.6
B
0.8
C
1.2
D
1.4
Question 83Single Answer
For a gas phase cracking reaction A→B+C at 300℃ , the Gibbs free energy of the reaction at this temperature is ∆G°= -2750J/mol . The pressure is 1 bar and the gas phase can be assumed to be ideal. The universal gas constant =8.314J/mol. K. The fractional molar conversion of A at equilibrium is________.
A
0.44
B
0.50
C
0.64
D
0.80
Question 84Single Answer
Which of the following statements are correct ?
1.In a ductile material elastic deformation is more predominant than plastic one.
2.Brittleness is not an absolute property of a metal.
3.Rate of loading has no influence in changing the behavior of a metal from ‘ductile’ to ‘brittle’ at low temperatures
4.Under hydrostatic compression, a brittle metal may change into a ductile one.
A
1 and 2
B
2 and 3
C
3 and 4
D
2 and 4
Question 85Single Answer
The total deflection of a structure when subjected simultaneously to different sets of loading is equal to the sum of the deflections under each such set of loads as if acting separately on the structure. Which one the following justifies this statement?
A
Elastic limit is not exceeded
B
Elastic limit including buckling is not exceeded
C
Limit state is not exceeded
D
Proportional limit without buckling is not exceeded
Question 86Single Answer
A rectangular bar of cross-sectional area a is subjected to an axial tensile load P. The maximum shear stress will occur on a plane at X° to any normal cross-section where X° is
A
90°
B
27°
C
180°
D
45°
Question 87Single Answer
A solid circular shaft has been subjected to a pure torsion moment. The ratio of maximum shear stress to maximum normal stress at any point would be
A
1 : 2
B
1 : 1
C
2 : 3
D
2 : 1
Question 88Single Answer
Which of the following statements are correct?
1.All load carrying members transmit load through basic modes of tension, compression, torsion and shear only.
2.Beams carry transverse loads.
3.Combined loading is a complicated loading.
4.Nature of internal forces decides the aspect of combines loading.
A
1 and 2
B
2 and 3
C
3 and 4
D
2 and 4
Question 89Single Answer
Identify the WRONG statement amongst the following:
A
steam distillation is used for mixtures that re immiscible with water.
B
Vacuum distillation is used for mixtures that are miscible with water.
C
Steam distillation is used for mixtures that are miscible with water.
D
vacuum distillation columns have larger diameter as compared to atmospheric columns for the same throughout
Question 90Single Answer
Which of the following statements are correct?
1.Experimental results on thin-walled tubes show that maximum normal stress theory is valid.
2.Normal-stress theory is valid in case of brittle materials.
3.In case of pure shear, St. Venant’s theory is more valid than other theories.
4.Tresca’s theory is very closely substantiated by experimental results.
5.In maximum stress theory, the yield locus is a hexagon.
A
1, 2 and 3
B
2, 4 and 5
C
1, 2 and 4
D
2, 3 and 4
Question 91Single Answer
A thin cylindrical shell made of mild steel plate is 1000 mm in diameter. It is to be subjected to an internal pressure of 2 N/mm2. If the material yields at 200N/mm2, the thickness of the plate in mm on the basis of Rankine’s theory of failure with assuming a factor of safety of 3 would be
A
10
B
12
C
15
D
18
Question 92Single Answer
Which of the following can change if only the catalyst is changed for a reaction system?
A
Enthalpy of reaction
B
Activation energy
C
Free Energy of the reaction
D
Equilibrium constant
Question 93Single Answer
Which of the following loads should be applied on a simply supported beam, so that the shear force is constant throughout its span?
A
U.D.L. over the entire span.
B
Two concentrated loads equally spaced in the span.
C
A central concentrated load and a U.D.L. over the entires pan.
D
A couple anywhere in the span.
Question 94Single Answer
A simply supported rolled steel joist of I-section has flange width 250 mm and overall depth 600 mm. Its moment of inertia IXX = 12 × 106 mm4. The steel joist is used as a beam over a simply supported span of 6m. It carries a load of 40 kN/m including its self weight throughout the span. The maximum stress induced in the beam in N/mm2 due to bending would be
A
30
B
90
C
45
D
60
Question 95Single Answer
Which of the following terms represents the torque that produces a twist of one radian in a shaft of unit length?
A
Torsional stress
B
Torsional rigidity
C
Flexural rigidity
D
Moment of resistance
Question 96Single Answer
A 60 mm dia. shaft is subjected to a torque of 6 kN-m. C = 8 × 104 N/mm2. The maximum shear stress induced in the shaft in N/mm2will be
A
8000
92
B
4000
9
C
12000
9
D
16000
9
Question 97Single Answer
A water main 160 cm dia. contains water at a pressure head of 200m. Take weight of water to be 1000 kg/m3. The thickness of the metal shell required for the water main, given that the maximum permissible stress in the metal is 400kg/cm2, will be
A
1 cm
B
2 cm
C
3 cm
D
4 cm
Question 98Single Answer
The radial splits which are wider on the outside of the log and narrower towards the pith are known as
A
Star shakes
B
Annular rings
C
Cup shakes
D
Hear shakes
Question 99Single Answer
Consider the following distinguishing characteristics of hardwood:
1.They have distinct annular rings.
2.They are not resinous.
Which of these characteristics of hardwood is/are correct?
A
1 only
B
2 only
C
Both 1 and 2
D
Neither 1 nor 2
Question 100Single Answer
Consider the following statements on the specific gravity of wood:
1.It is always greater than 2.
2.It is less than 1.
3.It is not dependent upon temperature and equilibrium moisture content.
Which of these statements are correct?
A
1, 2, 3 and 4
B
1 and 3 only
C
2 and 3 only
D
2 and 4 only
Question 101Single Answer
The age of a log of timber can be estimated by
A
Diameter of pith
B
Thickness of bark
C
Number of annular rings
D
Number of medullary rays
Question 102Single Answer
Consider the following statements:Seasoning of timber results in
1.Increased strength
2.Increased durability
3.Reduced resilience
4.Increased dimensional stability
Which of these statements are correct?
A
1, 2 and 4
B
1, 2 and 3
C
1, 3 and 4
D
2, 3 and 4
Question 103Single Answer
Match List-I and List-II and select the correct answer using the code given below the lists: List-I List-II
Plywood 1. Furniture
Fiberboard 2. Cantilever arches
Laminated lumber 3. Insulation
Commercial blockboard 4. Lining of form-work in concrete Codes:
A
A B C D
1 2 3 4
B
4 3 2 1
C
4 2 3 1
D
4 2 3 1
Question 104Single Answer
Consider the following statements:Perforated bricks are preferred in construction since
1.They are lighter
2.They are stronger than class 1 bricks
3.They have heat-insulating properties
4.They are cheaper and need less mortar
Which of these statements are correct?
A
1, 2, 3 and 4
B
2 and 3 only
C
1 and 3 only
D
3 and 4 only
Question 105Single Answer
The standard size of a brick is
A
20 cm × 10 cm × 10 cm
B
19 cm × 9 cm × 9 cm
C
18 cm × 9 cm × 9 cm
D
18 cm × 10 cm × 10 cm
Question 106Single Answer
Consider the following statements:More than 6% magnesium oxide by weight in cement results in
1.High early strength and high heat generation
2.Less tendency towards volume change and formation of cracks
Which of these statements is/are correct?
A
1 only
B
2 only
C
Neither 1 nor 2
D
Both 1 and 2
Question 107Single Answer
Fineness if cement is measured in the units of
A
Volume/mass
B
Mass/volume
C
Area/mass
D
Mass/area
Question 108Single Answer
The initial setting time of cement depends most on
A
Tricalcium aluminate
B
Tricalciumaluminoferrite
C
Dicalcium silicate
D
Dicalcium silicate
Question 109Single Answer
Consider the following statements:Sand in cement mortar is used for
1.Increasing the strength
2.Reducing the shrinkage
3.Decreasing the surface area of the binding material
4.Decreasing the quantity of cement
Which of these statements are correct?
A
1, 2 and 4
B
1, 2 and 3
C
1, 3 and 4
D
2, 3 and 4
Question 110Single Answer
Consider the following statements:
1.The compressive strength of concrete decreases with increase in water-cement ratio of the concrete mixture.
2.Water is added to the concrete mix for hydration of cement and workability.
3.Creep and shrinkage of concrete are independent of the water-cement ratio in the concrete mix.
Which of these statements are correct?
A
1 and 4 only
B
1 and 3 only
C
2 and 3 only
D
1, 2 and 3
Question 111Single Answer
According to the Indian Standard Specifications, concrete should be cured under a humidity of
A
90%
B
80%
C
60%
D
70%
Question 112Single Answer
Consider the following statements:In a typical compression test with a cylindrical concrete specimen, failure is initiated by
1.Crushing in compression
2.Inclined shear failure
3.Longitudinal tensile cracks
Which of these statements are correct?
A
1 only
B
2 only
C
3 only
D
1, 2 and 3
Question 113Single Answer
If one intends to obtain the best workability of concrete, the preferred shape of aggregate is
A
Round
B
Annular
C
Triangular
D
Flinty
Question 114Single Answer
Consider the following statements as regards rheology of concrete:
1.It deals with strength of concrete.
2.It deals with deformation in concrete.
3.It is the study of deformation and flow of concrete.
4.It deals with rate of shear and shear stress in concrete.
Which of these statements are correct?
A
1, 2, 3 and 4
B
3 and 4 only
C
2 and 3 only
D
1 and 2 only
Question 115Single Answer
Consider the following for durability of well-graded concrete:
1.The environment
2.Cover to embedded reinforcement
3.Shape and size of concrete member
Which of these are correct?
A
1 and 2 only
B
1 and 3 only
C
2 and 3 only
D
1, 2 and 3
Question 116Single Answer
Consider the common methods related to testing of concrete:
1.Consistency
2.Compacting factor
3.Vee-Bee
4.Setting time
5.Slump
Which of these methods refer to measuring workability ofconcrete?
A
1, 2 and 3
B
1, 2 and 5
C
2, 3 and 4
D
2, 3 and 5
Question 117Single Answer
Gypsum is added into the raw materials during manufacture of cement so that the final product exhibits
A
Retarded initial setting time
B
Improved mouldability for cornices, etc
C
Increases compressive strength
D
Augmented bond strength
Question 118Single Answer
Consider the following constituents of a high performance concrete (HPC):
1.Cement
2.Fine aggregate
3.Coarse aggregate
4.Water
5.Mineral admixture
6.Chemical admixture
Which of these constituentsare relevant for HPC?
A
1, 2, 3, 4, 5 and 6
B
1, 2, 3, 4 and 5 only
C
2, 3, 4, 5 and 6 only
D
1, 2, 3, 5 and 6 only
Question 119Single Answer
A specimen is subjected to a pure shear stress regime of intensity.The resulting tensile and compressive stresses, which occur on planes inclined at 45° to the direction of the shear stresses, would be
A
T
B
T
2
C
T2
D
T3
Question 120Single Answer
For a given elastic material, the Elastic modulus E is 210 GPa and its Poisson’s ratio is 0.27. What is the approximate value if its modulus of Rigidity ?
A
105 GPa
B
83 GPa
C
159 GPa
D
165 GPa
Question 121Single Answer
Which of the following is not a basic type of strain ?
A
Compressive strain
B
Shear strain
C
Area strain
D
Volume strain
Question 122Single Answer
Young's Modulus of elasticity is
A
Tensile stress / Tensile strain
B
Shear stress / Shear strain
C
Tensile stress / Shear strain
D
Shear stress / Tensile strain
Question 123Single Answer
Which of the following stresses is measured on inclined surface in Mohr’s Circle Method ?
A
Principal stress
B
Normal stress
C
Tangential stress
D
Maximum stress
Question 124Single Answer
Hooke's law is applicable within
A
Elastic limit
B
Plastic limit
C
Fracture point
D
Ultimate strength
Question 125Single Answer
Lead, as a material used in construction, has E = 15 GPa and K = 50 GPa. What is its Poisson’s ratio?
A
0.225
B
0.30
C
0.40
D
0.45
Question 126Single Answer
Crushing strength of good building stone should be more than:
A
500 kg/cm2
B
1000 kg/cm2
C
1400 kg/cm2
D
2000 kg/cm2
Question 127Single Answer
Two planks each of 50 mm × 50 mm section are glued together along the length to form as section 50 mm × 100 mm; and used as a beam. If the shear force at the section is 1000 N, what is the maximum shear stress on the glue?
A
0.15 MPa
B
0.3MPa
C
0.6MPa
D
2.4MPa
Question 128Single Answer
The probability distribution taken to represent the completion time in PERT analysis is
A
Gamma distribution
B
Normal distribution
C
Beta distribution
D
Log-normal distribution
Question 129Single Answer
The state of stress at a point in 2-D stress system is characterized by direct stresses of 40 MPa compressive and 80 MPa tensile, on mutually perpendicular planes. Shear stress is absent on these planes. The maximum shear stress sat this point (along a duly identified plane) is
A
20 MPa
B
40MPa
C
60MPa
D
80MPa
Question 130Single Answer
An electrical resistance strain rosette indicates strain of -400, +800 and +500 along the x,y and 45° axes. What is the shearing ratio yxy?
A
100
B
800
C
600
D
-200
Question 131Single Answer
In a diagonal scale only
A
Units can be shown
B
Units, tenths can be shown
C
Units, tenths, hundredths can be shown
D
Units, tenths, hundredths and thousandths can be shown
Question 132Single Answer
A cylindrical pressure vessel is 1200 mm in diameter. It is made of rolled mild steel plate. The vessel is subjected to an internal pressure of 2 N/mm2. If the material yields at 200 N/mm2, what should be the minimum safe thickness of the plate, based on Maximum Principle Stress Theory?
A
18 mm
B
15 mm
C
12 mm
D
9 mm
Question 133Single Answer
The constituent compound in Portland cement which reacts immediately with water, and also sets earliest, is
A
Tricalcium silicate
B
Dicalcium silicate
C
Tricalcium aluminate
D
Tetracalcium aluminoferrite
Question 134Single Answer
A simply subjected beam of length 4 m is subjected to a uniformly distributed load of 2 kN/m. What is the maximum shear stress is the cross-section is rectangular, 100 mm wide and 200 mm deep?
A
0.2 N/mm2
B
0.1 N/mm2
C
0.4 N/mm2
D
0.3 N/mm2
Question 135Single Answer
A mild steel structural section is an unsymmetrical I-section, with the greater width at the top and the smaller width at the bottom. The overall depth of the beam is 300 mm, and the flange stresses at the top and the bottom of the beam are 150 N/mm2and 50 N/mm2 respectively. What is the height of the neutral axis of the beam from its bottom?
A
125 mm
B
100 mm
C
75 mm
D
50 mm
Question 136Single Answer
The surveying used to determine additional details such as boundaries of fields, is called
A
City surveying
B
Location surveying
C
Cadastral surveying
D
Topographical surveying
Question 137Single Answer
A circular shaft of diameter ‘D’ is made of a material for which the Young’s modulus of elasticity is ‘E’ and Poisson’s ratio is ‘v’. the ratio of flexural rigidity to torsional rigidity for the shaft is
A
4(1+v)
B
1.5(1-2v)
C
(1+v)
D
0.25(1+v)
Question 138Single Answer
A closely coiled helical spring of round steel wire 5mm in diameter having 12 complete coils of 50 mm mean diameter is subjected to an axial load of 100 N. Modulus of rigidity of the spring is 80kn/mm2. What is the deflection of the spring?
A
12 mm
B
24 mm
C
36 mm
D
48 mm
Question 139Single Answer
What is the shear stress at the neutral axis in a beam of isosceles triangular section with a base of 40 mm and height 20 mm subjected to a shear force of 2 kN?
A
3 MPa
B
6MPa
C
10MPa
D
20MPa
Question 140Single Answer
A beam of square cross-section is placed such that its neutral axis coincides with its diagonal, and it is subjected to a shear force F. What is the ratio of the maximum shear stress to the shear stress at the neutral axis?
A
9
8
B
8
9
C
7
8
D
8
7
Quantitative Aptitude
Question 141Single Answer
If A exceeds B by 40%, B is less than C by 20%, then A C is,:
A
28 : 25
B
26 : 25
C
3 : 2
D
3 : 1
Question 142Single Answer
What is the sum of 130+125+191 ?
A
335
B
456
C
446
D
426
Question 143Single Answer
If , then x is equal to
A
5
B
3
C
2
D
4
Question 144Single Answer
A sum of money doubles itself at compound interest in 15 years. In how many years it will become eight times ?
A
30
B
45
C
50
D
60
Question 145Single Answer
Compound interest (compounded annually) on a certain sum of money for 2 years at 4% per annum is Rs. 102. The simple interest on the same sum for the same rate and for the same period will be
A
Rs. 99
B
Rs. 101
C
Rs. 100
D
Rs. 98
Question 146Single Answer
There are 5 red balls, 4 yellow balls and 3 green balls in a basket. If 3 ball are drawn at random. What is the probability that at least 2 of them are green in colour?
A
B
C
D
E
Question 147Single Answer
Which of the following fractions is in descending order ?
A
B
C
D
Question 148Single Answer
The value of
A
9
B
7
C
11
D
Question 149Single Answer
The square root of is
A
B
C
D
Question 150Single Answer
If (1101)2 = 1212201 find the value at
A
110.1
B
11.01
C
1.101
D
11.001
Question 151Single Answer
A discount of 15% on one article is the same as discount of 20% on a second article. The costs of the two articles can be
A
Rs. 85, Rs. 60
B
Rs. 60, Rs. 40
C
Rs. 40, Rs. 20
D
Rs. 80, Rs. 60
Question 152Single Answer
is equal to
A
-2
B
2
C
0
D
1
Question 153Single Answer
Four number-pairs have been given, out of which three are alike in some manner and one is different. Select the number-pair that is different.
A
28 : 163
B
16 : 91
C
27 : 82
D
22 : 127
Question 154Single Answer
The simplified value of is
A
0.075
B
0.705
C
0.750
D
7.500
Question 155Single Answer
The digit in unit's place of the number
(1570)2 + (1571)2 + (1572)2 + (1573)2 is
A
4
B
1
C
2
D
3
Question 156Single Answer
Select the letter-cluster from among the given options that can replace the question mark (?) in the following series.
MEND, PHJZ, SKFV, VNBR, ?
A
YJYN
B
YQXN
C
YRXO
D
YQZM
Question 157Single Answer
Select the option in which the numbers are related in the same way as are the numbers of the following set.
(12, 14, 143)
A
(12, 18, 246)
B
(17, 12, 134)
C
(16, 10, 235)
D
(15, 19, 252)
Question 158Single Answer
=?
A
4
B
6
C
8
D
10
Question 159Single Answer
Select the option in which the numbers are NOT related in the same way as are the numbers of the following set.
(64, 91, 118)
A
(46, 73, 101)
B
(48, 75, 102)
C
(72, 99, 126)
D
(55, 82, 109)
Question 160Single Answer
is equal to
A
12.0
B
11.5
C
11.0
D
10.5
Question 161Single Answer
The simplified value of is
A
3
B
2
C
4
D
6
Question 162Single Answer
Given that = 3.6 and = 11.4, then the value of is equal to
A
36.164
B
37.254
C
36.254
D
37.154
Question 163Single Answer
The monthly income of three cricketers Ankit, Sanjay and Roshan, from different sources, are in the ratio of 12 : 9 : 7, and their expenditures are in the ratio 15 : 9 : 8. If Ankit saves 25% of his income for future investments, what is the ratio of the savings of Ankit, Sanjay and Roshan?
A
15 : 18 : 11
B
25 : 16 : 13
C
5 : 8 : 7
D
23 : 18 : 11
Question 164Single Answer
Given that is approximately equal to 4898, is nearly equal to
A
0.544
B
1.333
C
1.633
D
2.666
Question 165Single Answer
Which of the following numbers 0.1, 0.01, (0.11)2, is greatest?
A
0.1
B
0.01
C
(0.11)2
D
Current Affairs
Question 166Single Answer
Which city hosted the 9th IONS Conclave of Chiefs 2026?
A
Kochi
B
Mumbai
C
Visakhapatnam
D
Goa
Question 167Single Answer
Which country will host the AI Summit after India AI Impact Summit 2026?
A
USA
B
Germany
C
Switzerland
D
Japan
Question 168Single Answer
Which country is scheduled to host the G7 Summit 2026?
A
Italy
B
Germany
C
France
D
Canada
Question 169Single Answer
Which country will host the SCO Summit 2026?
A
India
B
Kyrgyzstan
C
Kazakhstan
D
China
Question 170Single Answer
Which country will host the ASEAN Summit 2026?
A
Thailand
B
Indonesia
C
Philippines
D
Malaysia
Question 171Single Answer
Where is the headquarters of the BRICS Summit 2026 expected to be hosted?
A
New Delhi
B
Mumbai
C
Bengaluru
D
Ahmedabad
Question 172Single Answer
Which ministry introduced the Swasth Bharat Portal?
A
Ministry of Women and Child Development
B
Ministry of Education
C
Ministry of Health and Family Welfare
D
Ministry of AYUSH
Question 173Single Answer
India's first green methanol project is located in which state?
A
Gujarat
B
Rajasthan
C
Maharashtra
D
Odisha
Question 174Single Answer
Mission Mausam was launched by which ministry?
A
Ministry of Earth Sciences
B
Ministry of Environment
C
Ministry of Science and Technology
D
Ministry of Agriculture
Question 175Single Answer
National Technology Day is observed in India on which date?
A
10 May
B
11 May
C
12 May
D
15 May
Question 176Single Answer
Which organization publishes the World Economic Outlook report?
A
OECD
B
WTO
C
IMF
D
World Bank
Question 177Single Answer
What was the theme of the 9th IONS Conclave of Chiefs 2026?
A
Maritime Security First
B
Indo-Pacific Cooperation
C
Maritime Cooperation for Humanitarian Support
D
Blue Economy Growth
Question 178Single Answer
Which country holds the BRICS Chairmanship in 2026?
A
Brazil
B
Russia
C
China
D
India
Question 179Single Answer
What was the theme of BioAsia International Summit 2026?
A
AI for Humanity
B
Future of Biotechnology
C
TechBio Unleashed: AI, Automation & the Biology Revolution
D
Digital Health Revolution
Question 180Single Answer
Which city hosted the 23rd BioAsia International Summit 2026?
A
Mumbai
B
Chennai
C
Bengaluru
D
Hyderabad
Question 181Single Answer
The Rajasthan AI-ML Policy 2026 was launched during which conference?
A
Digital India Summit
B
AI Action Summit
C
Regional AI Impact Conference 2026
D
India AI Impact Summit
Question 182Single Answer
Which city hosted the Regional AI Impact Conference 2026?
A
Chennai
B
Jaipur
C
Pune
D
Kochi
Question 183Single Answer
Which country is expected to host COP31 Climate Summit 2026?
A
France
B
UAE
C
Germany
D
Turkey
Question 184Single Answer
Which country is scheduled to host the BRICS Summit 2026?
A
China
B
India
C
South Africa
D
Brazil
Question 185Single Answer
Which city is expected to host the G20 Summit 2026?
A
New York
B
Washington D.C.
C
Miami
D
Los Angeles
Question 186Single Answer
Which ministry organized the India AI Impact Summit 2026?
A
Ministry of Science and Technology
B
Ministry of Electronics and Information Technology
C
Ministry of Commerce
D
Ministry of Education
Question 187Single Answer
Where was the India AI Impact Summit 2026 organized?
A
Pragati Maidan, Delhi
B
Vigyan Bhawan, New Delhi
C
Bharat Mandapam, New Delhi
D
Hyderabad International Convention Centre
Question 188Single Answer
Which summit on Artificial Intelligence was hosted by India in February 2026?
A
World AI Congress
B
AI Action Summit
C
India AI Impact Summit 2026
D
Global AI Forum
Question 189Single Answer
Where was the BRICS Foreign Ministers' Meeting held in May 2026?
A
Mumbai
B
Hyderabad
C
Bengaluru
D
New Delhi
Question 190Single Answer
What is the theme of India’s BRICS Chairmanship 2026?
A
Inclusive Growth for All
B
Sustainable Global Economy
C
One Earth One Future
D
Building for Resilience, Innovation, Cooperation and Sustainability