๐Ÿ“š Exam by Category
โ–พ
Objective Questions

Latest GATE Agricultural Engineering Exam Question (Objective Questions), MCQ in English

Subjects : General Aptitude, Engineering Mathematics, Agricultural Engineering

Question Bank GATE Agricultural Engineering Exam (Only MCQ) - English
Back to Exam

General Aptitude

Question 1Single Answer
Inhaling the smoke from a burning _____ could _____ you quickly.
  1. A
    tire/tier
  2. B
    tire/tyre
  3. C
    tyre/tire
  4. D
    tyre/tier
Question 2Single Answer
Rice, a versatile and inexpensive source of carbohydrate, is a critical component of diet worldwide. Climate change, causing extreme weather, poses a threat to sustained availability of rice. Scientists are working on developing Green Super Rice (GSR), which is resilient under extreme weather conditions yet gives higher yields sustainably.
Which one of the following is the CORRECT logical inference based on the information given in the above passage ?
  1. A
    GSR is an alternative to regular rice, but it grows only in an extreme weather
  2. B
    GSR be used in future in response to adverse effects of climate change
  3. C
    GSR grows in an extreme weather, but the quantity of produce is lesser than regular rice
  4. D
    Regular rice will continue to provide good yields even in extreme weather
Question 3Single Answer
The cost price of 20 articles is the same as the selling price of x articles. If the profit is 25%, then the value of x is :
  1. A
    15
  2. B
    16
  3. C
    18
  4. D
    25
Question 4Single Answer
Pipes P and Q can fill a storage tank full of water in 10 and 6 minutes, respectively. Pipe R draws the water out from the storage tank at a rate of 34 litres per minute. P, Q and R operate at a constant rate. If it takes one hour to completely empty a full storage tank with all the pipes operating simultaneously, what is the capacity of the storage tank (in litres) ?ย 
  1. A
    26.8ย 
  2. B
    60.0ย 
  3. C
    120.0
  4. D
    127.5
Question 5Single Answer
Choose the grammatically correct sentence?
  1. A
    Neither of the robots are functioning properly
  2. B
    Neither robots is functioning properly
  3. C
    Neither of the robot are functioning properly
  4. D
    Neither of the robots is functioning properly

Engineering Mathematics

Question 6Single Answer
Consider the following expression :
where z, y, and t are variables, andย  ย is a complex number. The partial differential equation derived from the above expression is
  1. A
  2. B
  3. C
  4. D
Question 7Single Answer
If (A=\begin{bmatrix}1&2\3&4\end{bmatrix}), what is (\det(A))?
  1. A
    2
  2. B
    (-2)
  3. C
    5
  4. D
    10
Question 8Single Answer
If (A) is a (3\times3) matrix with (\det(A)=5), what is (\det(2A))?
  1. A
    10
  2. B
    40
  3. C
    20
  4. D
    80
Question 9Single Answer
In Gaussian elimination, the main purpose of partial pivoting is to?
  1. A
    reduce round-off error and avoid division by a very small pivot
  2. B
    guarantee integer solutions
  3. C
    make the coefficient matrix symmetric
  4. D
    convert every matrix into a diagonal matrix
Question 10Single Answer
A system Ax = b has a unique solution when A is square and?
  1. A
    all diagonal entries are zero
  2. B
    det(A) is nonzero
  3. C
    A has two identical rows
  4. D
    det(A) is zero

Agricultural Engineering

Question 11Single Answer
In a spur gear for a farm machinery application with a module of 5 mm and 20 teeth, operating at 1200 rpm, what is the pitch line velocity?
  1. A
    6.28 m/s
  2. B
    7.54 m/s
  3. C
    8.80 m/s
  4. D
    9.42 m/s
Question 12
A V-belt drive in a tractor has a contact angle of 150ยฐ and a coefficient of friction of 0.
    Question 13Single Answer
    If the tension ratio (T1/T2) is 2.5 and belt speed is 12 m/s, what is the power transmitted if T1 = 1000 N?
    1. A
      7.5 kW
    2. B
      8.5 kW
    3. C
      8.0 kW
    4. D
      9.0 kW
    Question 14Single Answer
    A shaft in a farm implement is subjected to a bending moment of 600 Nm and a torque of 400 Nm. If the material yield strength is 450 MPa with a safety factor of 2, what is the minimum shaft diameter using maximum shear stress theory?
    1. A
      25 mm
    2. B
      30 mm
    3. C
      35 mm
    4. D
      40 mm
    Question 15Single Answer
    In a chain drive for a harvester, the sprocket has 30 teeth and a pitch of 12.7 mm. If it rotates at 800 rpm, what is the chain speed?
    1. A
      3.18 m/s
    2. B
      3.02 m/s
    3. C
      2.86 m/s
    4. D
      3.34 m/s
    Question 16Single Answer
    A pulley system in a farm machine has a diameter of 300 mm and transmits 10 kW at 1000 rpm. What is the torque on the pulley?
    1. A
      100.5 Nm
    2. B
      95.5 Nm
    3. C
      105.5 Nm
    4. D
      110.5 Nm
    Question 17Single Answer
    What is the factor of safety for a knuckle joint in a tillage implement if the ultimate tensile strength of the material is 600 MPa and the maximum stress experienced is 200 MPa?
    1. A
      2
    2. B
      4
    3. C
      3
    4. D
      5
    Question 18Single Answer
    A bearing in a tractor axle is subjected to a radial load of 15 kN and an axial load of 5 kN. If the bearing life is rated for 10,000 hours at 500 rpm, what is the equivalent dynamic load?
    1. A
      16.5 kN
    2. B
      19.5 kN
    3. C
      18.5 kN
    4. D
      17.5 kN
    Question 19Single Answer
    In a gear system for a farm sprayer, the gear ratio is 3:1, and the input gear rotates at 1800 rpm. What is the output gear speed?
    1. A
      500 rpm
    2. B
      800 rpm
    3. C
      700 rpm
    4. D
      600 rpm
    Question 20Single Answer
    A coupling in a farm machine is designed to transmit 8 kW at 1200 rpm. If the shear strength of the coupling material is 300 MPa, what is the minimum diameter of the coupling pin?
    1. A
      10 mm
    2. B
      14 mm
    3. C
      12 mm
    4. D
      16 mm
    Question 21Single Answer
    What is the primary function of an overload safety clutch in a tractorโ€™s PTO system?
    1. A
      Increase power transmission
    2. B
      Prevent mechanical damage
    3. C
      Reduce fuel consumption
    4. D
      Enhance gear efficiency
    Question 22Single Answer
    A key in a farm machinery shaft transmits a torque of 500 Nm. If the key is 10 mm wide and 8 mm high, what is the shear stress in the key?
    1. A
      62.5 MPa
    2. B
      78.1 MPa
    3. C
      93.7 MPa
    4. D
      109.4 MPa
    Question 23Single Answer
    A belt drive system in a thresher has a pulley diameter of 400 mm and operates at 900 rpm. What is the belt speed?
    1. A
      20.35 m/s
    2. B
      18.85 m/s
    3. C
      21.85 m/s
    4. D
      23.35 m/s
    Question 24Single Answer
    In a farm implement, a shaft experiences a bending moment of 800 Nm and a torque of 600 Nm. If the safety factor is 2.5 and the material yield strength is 500 MPa, what is the minimum shaft diameter?
    1. A
      32 mm
    2. B
      40 mm
    3. C
      36 mm
    4. D
      44 mm
    Question 25Single Answer
    A sprocket in a chain drive system has 25 teeth and a pitch of 15 mm. If it rotates at 600 rpm, what is the chain speed?
    1. A
      2.36 m/s
    2. B
      2.83 m/s
    3. C
      3.30 m/s
    4. D
      3.77 m/s
    Question 26Single Answer
    A gear in a tractorโ€™s transmission system has a pressure angle of 20ยฐ and a module of 6 mm. If the gear has 30 teeth, what is the pitch circle diameter?
    1. A
      160 mm
    2. B
      180 mm
    3. C
      170 mm
    4. D
      190 mm
    Question 27Single Answer
    A bearing in a farm machine is subjected to a radial load of 20 kN and an axial load of 8 kN. If the bearing life is rated for 12,000 hours at 600 rpm, what is the equivalent dynamic load?
    1. A
      22.4 kN
    2. B
      23.6 kN
    3. C
      24.8 kN
    4. D
      26.0 kN
    Question 28Single Answer
    In a pulley system for a farm sprayer, the input pulley rotates at 1500 rpm with a diameter of 200 mm, and the output pulley has a diameter of 400 mm. What is the output pulley speed?
    1. A
      600 rpm
    2. B
      700 rpm
    3. C
      750 rpm
    4. D
      800 rpm
    Question 29Single Answer
    A knuckle joint in a tillage implement is subjected to a tensile load of 50 kN. If the material has an ultimate tensile strength of 700 MPa and a safety factor of 3, what is the minimum pin diameter?
    1. A
      16 mm
    2. B
      14 mm
    3. C
      12 mm
    4. D
      18 mm
    Question 30Single Answer
    What is the primary advantage of using a shear pin as an overload safety device in farm machinery?
    1. A
      High durability
    2. B
      Low cost and easy replacement
    3. C
      High power transmission
    4. D
      Low maintenance
    Question 31Single Answer
    A shaft in a farm machine transmits 15 kW at 1800 rpm. If the shear strength of the material is 350 MPa, what is the minimum shaft diameter?
    1. A
      20 mm
    2. B
      24 mm
    3. C
      22 mm
    4. D
      26 mm
    Question 32Single Answer
    A gear system in a farm implement has a gear ratio of 4:1, and the input gear rotates at 2000 rpm. What is the output gear speed?
    1. A
      500 rpm
    2. B
      400 rpm
    3. C
      600 rpm
    4. D
      700 rpm
    Question 33
    A belt drive in a tractor has a contact angle of 170ยฐ and a coefficient of friction of 0.
      Question 34Single Answer
      If the tension ratio (T1/T2) is 3.2 and T1 = 1500 N, what is the power transmitted at a belt speed of 15 m/s?
      1. A
        18.0 kW
      2. B
        16.5 kW
      3. C
        15.0 kW
      4. D
        19.5 kW
      Question 35Single Answer
      A coupling in a farm machine is designed to transmit 12 kW at 1000 rpm. If the shear strength of the coupling material is 320 MPa, what is the minimum diameter of the coupling pin?
      1. A
        12 mm
      2. B
        16 mm
      3. C
        14 mm
      4. D
        18 mm
      Question 36Single Answer
      The primary function of a gear drive is to transmit:
      1. A
        Heat only
      2. B
        Rotary motion and power
      3. C
        Fluid pressure
      4. D
        Electrical energy
      Question 37Single Answer
      Two external spur gears in mesh rotate in:
      1. A
        Opposite directions
      2. B
        The same direction
      3. C
        Random directions
      4. D
        Axial directions
      Question 38Single Answer
      The gear ratio for a simple gear pair is equal to:
      1. A
        Driven teeth รท driver teeth
      2. B
        Driver teeth รท driven teeth
      3. C
        Sum of teeth on both gears
      4. D
        Difference between gear teeth
      Question 39Single Answer
      If a 20-tooth gear drives a 60-tooth gear, the velocity ratio is:
      1. A
        1
      2. B
        2
      3. C
        3
      4. D
        4
      Question 40Single Answer
      A gear having teeth parallel to the axis of rotation is called a:
      1. A
        Bevel gear
      2. B
        Worm gear
      3. C
        Spur gear
      4. D
        Hypoid gear
      Question 41Single Answer
      Helical gears are generally smoother than spur gears because:
      1. A
        They have no teeth
      2. B
        They operate without lubrication
      3. C
        They transmit no axial force
      4. D
        Tooth engagement is gradual
      Question 42Single Answer
      Bevel gears are commonly used between shafts whose axes:
      1. A
        Are always parallel
      2. B
        Cannot rotate
      3. C
        Are always coincident
      4. D
        Intersect each other
      Question 43Single Answer
      A worm and worm wheel arrangement is suitable for obtaining:
      1. A
        Very small speed reduction
      2. B
        Large speed reduction
      3. C
        No torque multiplication
      4. D
        Linear motion only
      Question 44Single Answer
      The pitch circle of a gear is an imaginary circle that:
      1. A
        Passes through tooth roots only
      2. B
        Represents theoretical rolling contact
      3. C
        Gives shaft diameter
      4. D
        Defines bearing clearance
      Question 45Single Answer
      Module of a gear is defined as:
      1. A
        Number of teeth รท pitch diameter
      2. B
        Addendum รท dedendum
      3. C
        Circular pitch ร— number of teeth
      4. D
        Pitch diameter รท number of teeth
      Question 46Single Answer
      The SI unit normally used for gear module is:
      1. A
        mmยฒ
      2. B
        mm
      3. C
        rad/s
      4. D
        N
      Question 47Single Answer
      Circular pitch of a gear is related to module m by:
      1. A
        p = ฯ€m
      2. B
        p = m/ฯ€
      3. C
        p = ฯ€/m
      4. D
        p = mยฒ
      Question 48Single Answer
      The addendum of a gear tooth is the radial distance between the:
      1. A
        Root circle and shaft
      2. B
        Pitch circle and addendum circle
      3. C
        Base circle and shaft
      4. D
        Two pitch circles
      Question 49Single Answer
      The dedendum of a gear tooth is measured between the:
      1. A
        Pitch and root circles
      2. B
        Addendum and pitch circles
      3. C
        Shaft and pitch circle
      4. D
        Base and addendum circles
      Question 50Single Answer
      Backlash in gears is the difference between:
      1. A
        Addendum and dedendum
      2. B
        Gear and shaft diameter
      3. C
        Tooth space and tooth thickness measured along pitch circle
      4. D
        Pitch and root diameter
      Important Questions Package

      GATE Agricultural Engineering Exam Online Question Bank Package

      Buy GATE Agricultural Engineering Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in GATE Agricultural Engineering question bank 2026 in Online, PDF & Print study material.

      + Free Monthly Current Affairs, GK & more PDF Download
      Sr.Package NameAmount
      1.GATE Agricultural Engineering Exam (Only MCQ) - English
      Description : 1000 Question With Answer
      โ‚น101 [โ‚น500]
      2.GATE Agricultural Engineering Exam (Only MCQ) - English
      Description : 2000 Question With Answer
      โ‚น151 [โ‚น500]
      3.GATE Agricultural Engineering Exam (Only MCQ) - English
      Description : 3000 Question With Answer
      โ‚น171 [โ‚น500]
      4.GATE Agricultural Engineering Exam (Only MCQ) - English
      Description : 4000 Question With Answer
      โ‚น191 [โ‚น500]
      5.GATE Agricultural Engineering Exam (Only MCQ) Question Bank Book - English
      Description : 1000 Question with Answer (Printed Material)
      โ‚น390 [โ‚น650]
      6.GATE Agricultural Engineering Exam (Only MCQ) - English
      Description : 1000 Question & Answer Download in PDF (Send by Email)
      โ‚น390 [โ‚น650]
      7.GATE Agricultural Engineering Exam (Only MCQ) - English (old)
      Description : 1000 Question & Answer Download in PDF (Send by Email)
      โ‚น151 [โ‚น550]
      Back to Exam