A water supply distribution system for an averagely-populated township is to be designed for
A
Maximum daily demand
B
Maximum hourly demand and fire demand
C
Average demand
D
Maximum daily demand and fire demand or maximum hourly demand, whichever is higher
Question 2Single Answer
A combined sewerage system is more appropriate for developed areas where
A
Rainfall occurs for a very few days in a year
B
Rainfall occurs almost uniformly throughout the year
C
Air temperatures are nearly uniform throughout the year
D
Air temperatures through the year include extremes during certain runs of days
Question 3Single Answer
100 m3 of sludge holds a moisture content of 95%. If its moisture content chagnes to 90%, the volume of this sludge will then be
A
40.5m3
B
50m3
C
75m3
D
94.7m3
Question 4Single Answer
The design overflow rate of a sedimentation tank is chosen considering
A
Flow rate through the tank
B
Diameter of the particle intended to be removed
C
Volume of the sedimentation tank
D
Detention time in the tank
Question 5Single Answer
Consider the following statements in respect of flow equalization in a waste water treatment plant :
1. Biological treatment is enhanced because shock loadings are eliminated or minimized
2. Flow equalizations is an attractive option for upgrading the performance of overloaded treatment plants.
3. Inhibiting substances can be diluted and pH can be stabilized
4. Thickening performance of primary sedimentation tanks following grit removal is improved.
Which of the above statements are correct?
A
1, 2, 3 and 4
B
1, 2 and 3 only
C
1, 2 and 4 only
D
3 and 4 only
Question 6Single Answer
A drain carrying 5m3/s of wastewater with its BOD of 100mg/l joins a stream carrying 50 m3/ s flow with its BOD of 5mg/l. What will be the value of the BOD of the combined flow after complete mixing?
A
3.6 mg/l
B
13.6 mg/l
C
33.6 mg/l
D
53.6 mg/l
Question 7Single Answer
Consider the following statements in respect of aerated grit chamber:
1. The grit accumulates at the bottom in advancing spiral-flow aeration tanks, location ally preceded by grit chambers, led to the eventual development of aerated grit chambers.
2. The excessive wear on grit handling equipment is a major factor for the popularity of aerated grit chambers.
3. Aerated grit chambers are designed to provide detention period of 1 minute at maximum rate of flow.
4. Diffusers are located at 0.45 m to 0.6 m above the bottom of teh chamber.
Which of the above statements are correct?
A
1, 2 and 3 only
B
3 and 4 only
C
1, 2 and 4 only
D
1, 2, 3 and 4
Question 8Single Answer
Quick sand condition occurs when
A
the void ratio of the soil becomes 1.0
B
the upward seepage pressure in soil becomes zero
C
the upward seepage pressure in soil becones equal to the saturated unit weight of he soil
D
the upward seepage pressure in soil becomes equal to he submerged unit weight of the soil
Question 9Single Answer
The side of a square land was measured as 150 m and is in error by 0.05 m. What is the corresponding error in the computed area of the land.
A
5 m2
B
25 m2
C
10 m2
D
20 m2
Question 10Single Answer
Consider the following statements in respect of anaerobic sludge digester:
1. It is less expensive compared to several other methods available.
2. Processing of separable solids impacts the environment to a minimum
3. Quantity of separated solids requiring disposal is minimal
4. Digested sludge is very readily dewaterable.
Which of the above statements are correct?
A
1, 2, 3 and 4
B
1, 2 and 3 only
C
3 and 4 only
D
1, 2 and 4 only
Question 11Single Answer
Consider the following statements :
1. There will be no defects in select grade timbers.
2. The codal values for strength of grade-II timer without defects may be reduced by 37.5%.
3. For timber used as columns, the permissible stress in ungraded timbers is adopted with a multiplying factor of 0.50.
4. In case of wind force and earthquakes, a modification factor of 1.33 is adopted. Which of the above statements are correct ?
A
1 and 3 only
B
1 and 4 only
C
2 and 4 only
D
2 and 3 only
Question 12Single Answer
Consider the following statements regarding timber :
1. The strength of timber increases by Kiln seasoning.
2. Cutting of wood is to be done prior to treatment.
3. Water seasoning is good for prevention of warping.
4. ASCU treatment enhances the strength of wood. Which of the above statements are correct ?
A
1, 2 and 3 only
B
2, 3 and 4 only
C
1, 3 and 4 only
D
1, 2, 3 and 4
Question 13Single Answer
Gase(s) emitted during rotting or decomposition of timber is /are mainly
A
Methane and Hydrogen
B
Hydrogen Sulphide
C
Carbonic acid and Hydrogen
D
Ammonia
Question 14Single Answer
Efflorescence of bricks is due to
A
Excessive burning of bricks
B
High silt content in brick clay
C
High porosity of bricks
D
Soluble salts present in parent clay
Question 15Single Answer
Disintegration of bricks masonry walls is primarily due to
1. Efflorescence
2. Magnesium sulphate in brick
3. Calcined clay admixtures
4. Kankar nodules
Which of the a above statements are correct ?
A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 16Single Answer
Consider the following test :
1. Transverse strength test
2. Water absorption test
3. Impact test
4. Breaking strength test
Which of the above are relevant to testing of tiles ?
A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 17Single Answer
Which of the following statements is/are correct regarding the strength of cement ?
1. Particle sizes less than 3 m increases the viscous nature of the cement.
2. Finer particles in cement can be replaced by fly-ash to improve the strength.
A
1 only
B
2 only
C
Both 1 and 2
D
Neither 1 nor 2
Question 18Single Answer
The constituent compound in Portland cement which reacts immediately with water, and also sets earliest, is
A
Tricalcium silicate
B
Dicalcium silicate
C
Tricalcium aluminate
D
Tetracalcium aluminoferrite
Question 19Single Answer
Which of the following statements are correct with regard to cement mortar ?
1. Workability of cement mortar can be improved by addition of lime.
2. Fly-ash cement is economical in plastering jobs.
3. Addition of saw dust improves workability.
4. Sand in mortar can be replaced by finely crushed fire bricks.
A
1, 2, 3 and 4
B
1, 2 and 3 only
C
3 and 4 only
D
1, 2 and 4 only
Question 20Single Answer
In a concrete mix of proportion 1 : 3 : 6, the actual quantity of sand, which is judged to have undergone 15% bulking, per unit volume of cement, will be
A
3.00
B
3.45
C
4.50
D
6.00
Question 21Single Answer
Consider the following statements:
1. IS 3583 refers to Burnt Clay Paving Bricks.
2. IS 5779 refers to Burnt Clay Soling Bricks.
3. IS 3952 refers to Burnt Clay Hollow Bricks.
4. IS 2222 refers to Burnt Clay Lay Bricks.
Which of the above statements are correct?
A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 22Single Answer
Consider the following statements:
1. A high aggregate impact value indicates strong aggregates.
2. A low aggregate crushing value indicates high crushing strength of aggregates.
3. Aggregates having elongation index values greater than 15% are generally considered suitable for pavement construction.
4. Flakiness index of aggregates should not be less than 25% for use in road construction.
Which of the above statements are correct?
A
2 and 3 only
B
2 and 4 only
C
1 and 3 only
D
1 and 4 only
Question 23Single Answer
Consider the following statements regarding refractory bricks in furnaces:
1. The furnace is fired at temperatures more than 1700°C.
2. Silica content in the soil should be less than 40%.
3. Water absorption of bricks should not exceed 10%
4. Chrome bricks are known as basic bricks. Which of the above statements are correct?
A
1 and 2 only
B
2 and 4 only
C
1 and 3 only
D
3 and 4 only
Question 24Single Answer
Consider the following statements about lime:
1. Calcination of limestone results in quick lime.
2. Lime produced from pure variety of chalk is hydraulic lime.
3. Hydrated lime is obtained by treating quick lime with water.
Which of the above statements are correct?
A
1, 2 and 3
B
1 and 2 only
C
2 and 3 only
D
1 and 3 only
Question 25Single Answer
Consider the following statements:
1. If more water is added to concrete for increasing its workability, it results into concrete of low strength.
2. No slump is an indication of a good workable concrete.
3. Higher the slump of concrete, lower will be its workability.
4. Workability of concrete is affected by water content as well as water-cement ratio.
Which of the above statements are correct?
A
1 and 3 only
B
2 and 3 only
C
1 and 4 only
D
2 and 4 only
Question 26Single Answer
Pozzolana used as an admixture in concrete has the following advantages:
1. It improves workability with lesser amount of water.
2. It increases the heat of hydration and so lets the concrete set quickly.
3. It increases the resistance of concrete to attack by salts and sulphates.
4. It leaches out calcium hydroxide.
Select the correct answer using the codes given below:
A
1, 2 and 3 only
B
1, 2 and 4 only
C
1, 3 and 4 only
D
2, 3 and 4 only
Question 27Single Answer
Consider the following statements regarding Cyclopean Concrete:
1. Size of aggregate is more than 150 mm.
2. Size of aggregate is less than 150 mm.
3. High slump.
4. High temperature rise due to heat of hydration.
Which of the above statements are correct?
A
1 and 3 only
B
1 and 4 only
C
2 and 3 only
D
2 and 4 only
Question 28Single Answer
A chain, working a crane, has sectional area of 625 mm2 and transmits a load of 10 kN. When the load is being lowered at a uniform rate of 40 m/min, the chain gets jammed suddenly at which time the length of the chain unwound is 10m. Assuming E = 200 GPa, the stress induced in the chain due to this sudden jamming is
A
100.6 N/mm2
B
120.4 N/mm2
C
140.2 N/mm2
D
160.0 N/mm2
Question 29Single Answer
In mild steel specimens subjected to tensile test cycle, the elastic limit in tension is raised and the elastic limit in compression is lowered, This is called
A
Annealing effect
B
Bauschinger effect
C
Strain rate effect
D
Fatigue effect
Question 30Single Answer
Consider the following statements :
1. The shear stress distribution across the section of a circular shaft subjected to twisting varies parabolically.
2. The shear stress at the centre of a circular shaft under twisting moment is zero
3. The shear stress at the extreme fibres of a circular shaft under twisting moment is maximum.
Which of the above statements is/are correct?
A
1, 2 and 3
B
1 only
C
2 only
D
3 only
Question 31Single Answer
One bag of Portland cement, 50 kg in weight, would normally have a bulk volume of
A
30 l
B
35 l
C
40 l
D
45 l
Question 32Single Answer
AsCu, a preservative for wood, developed by the Forest Research Institute, Dehradun, comprises of chemicals:
A
1 : 1 : 1
B
1 : 2 : 3
C
1 : 2 : 4
D
1 : 3 : 4
Question 33Single Answer
Consider the following statements related to autoclave bricks:
1.Less water absorption compared to other bricks.
2.Noise reduction
3.It is cheap compared to other types of bricks.
4.Requirement of bulk volume of mortar in joints being relatively less compared to other types of brick masonry.
5.Not recommended for outer walls.
Which of the above statements are relevant to the use of ‘autoclave’ bricks?
A
1, 2 and 4
B
1, 3 and 5
C
2, 3 and 4
D
2, 4 and 5
Question 34Single Answer
The minimum number of annular rings to be seen in every 2.54 cm in the radial direction from the core for timber to be classified as ‘Dense’ is
A
10
B
20
C
25
D
30
Question 35Single Answer
If the actual thickness of a brick masonry wall is 19 cm, its effective length is 2.70 m, its effective height is 2.82 m and its code specified stiffening coefficient is 1.2 then, for design considerations, the slenderness ratio of the wall will be taken as
A
11.8
B
12.4
C
14.2
D
14.8
Question 36Single Answer
Consider the following forms of water in a hydrated cement paste:
1.Capillary water
2.Chemically combined water
3.Interlayer water
4.Adsorbed water
Which of the above forms of water will, on its/their removal, cause shrinkage of the paste?
A
1, 2 and 3
B
1, 2 and 4
C
2, 3 and 4
D
1, 3 and 4
Question 37Single Answer
Consider the following statements:High early strength of cement is obtained as a result of
1.Fine grinding.
2.Decreasing the lime content
3.Burning at higher temperature
4.Increasing the quality of gypsum.
Which of the above statements are correct?
A
1 and 2
B
1 and 3
C
2 and 3
D
3 and 4
Question 38Single Answer
Consider the following statements related to ‘composite mortar’:
1.Addition of lime to cement mortar improves its workability
2.Composite mortar is obtained by adding 10% by weight of cement and mixing with water.
3.Composite mortar is not preferred in tall buildings.
4.Mechanical grinding is essential for developing composite mortar.Which of the above statements are true in this case?
A
1, 2 and 3 only
B
1, 3 and 4 only
C
2, 3 and 4 only
D
1, 2, 3 and 4
Question 39Single Answer
Consider the following statements related to ‘non-destructive testing’ of concrete:
1.Indentation test is used to assess the quality of concrete.
2.Resonant Frequency Method is based on a laboratory test.
3.Compressive strength of concrete is estimated through Pulse Velocity Measurement.
4.Dynamic modulus of Elasticity is determined by a Sonometer Test.
5.Thickness of concrete can be estimated by in-situ Rebound Hammer Test.
Which of the above statements are correct?
A
1, 2 and 3 only
B
1, 2 and 5 only
C
1, 2, 3 and 4 only
D
1, 2, 3, 4 and 5
Question 40Single Answer
What is the amount of water required for a workable RC of mix 1 : 2: 4 by weight., when W/C is 0-60 and unit weight of concrete is 2400 kg/m3?
A
165 l
B
205 l
C
245 l
D
285 l
Question 41Single Answer
What will be the depth of penetration of the plunger in Vicat Apparatus (IS : 5513 - 1976) from the bottom of the Vicat Mould, when the cement paste is tested for standard consistency, according to IS 4031 – 1988 ?
A
11 to 15 mm
B
8 to 10 mm
C
15 to 17 mm
D
5 to 7 mm
Question 42Single Answer
Two sewer pipelines A and B (having the same diameter and made of the same material) are laid at a bed slope of 1 in 225 and 1 in 625, respectively. Determine the ratio of their carrying capacities (QA to QB) .
A
B
C
1
D
Question 43Single Answer
Select the correct statement with respect to an over - reinforced cement concrete section under the working stress method .
A
The compressive stress in steel reaches the allowable limit before the maximum tensile stress in concrete reaches the allowable limit
B
Tensile steel stress and maximum compressive stress in concrete simultaneously reach their allowable limits
C
The allowable limiting stress is reached in concrete before the steel stress reaches the limiting value
D
The tensile stress in steel reaches the allowable limit before the maximum compressive stress in concrete reaches the allowable limit
Question 44Single Answer
A cantilever beam of span L is built - in at the support. It is restrained against lateral deflection and torsion at the free end. The effective length of compression flange for the beam as per IS 800 : 2007 is
A
0.5 L
B
0.85 L
C
2 L
D
0.75 L
Question 45Single Answer
What is the principle of plane surveying ?
A
Working from part to whole
B
Working from point to area
C
Working from angle to volume
D
Working from whole to part
Question 46Single Answer
According is IS 5968 : 1987, the minimum radius of radius of curve to be provided in the alignment of unlined canals carrying a discharge of less than 30 cumecs up to 15 cumecs is :
A
100 m
B
1000 m
C
600 m
D
150 m
Question 47Single Answer
A Pelton wheel is to be designed for a pitch diameter of 1 m and jet diameter of 0.1 m. The number of buckets on the runner computed by Taygun’s formula is :
A
20
B
25
C
15
D
10
Question 48Single Answer
What is the effect of fly ash in concrete ?
A
Reduces the secondary hydration process
B
Increases the heat of hydration
C
Increases the amount of air entrainment
D
Reduces the heat of hydration
Question 49Single Answer
As per IS 456 : 2000, the minimum grade of concrete to be used for plain concrete and reinforced concrete, respectively, in concrete works exposed directly along the sea coast are :
A
M 20 and M 30
B
M 20 and M 25
C
M 22 and M 40
D
M 15 and M 25
Question 50Single Answer
Identify the property that changes as a function of the geometrical dimensions of a section in structural materials :
A
Mass density
B
Moment of inertia
C
Poission’s ratio
D
Modulus of elasticity
Important Questions Package
ESE Civil Engineering Exam Online Question Bank Package
Buy ESE Civil Engineering Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in ESE Civil Engineering question bank 2026 in Online, PDF & Print study material.
+ Free Monthly Current Affairs, GK & more PDF Download
Sr.
Package Name
Amount
1.
ESE Civil Engineering Stage-I Prelims Paper II Exam - English
Description : 1000 Question with Answer
₹101[₹500]
2.
ESE Civil Engineering Stage-I Prelims Paper II Exam - English
Description : 2000 Question with Answer
₹151[₹500]
3.
ESE Civil Engineering Stage-I Prelims Paper II Exam - English
Description : 3000 Question with Answer
₹181[₹500]
4.
ESE Civil Engineering Stage-I Prelims Paper II Exam - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151[₹450]
5.
ESE Civil Engineering Stage-I Prelims Paper II Exam Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390[₹600]
6.
ESE Civil Engineering Exam Paper 2 - English (Old)
Description : 2000 Question with Answer
₹141[₹500]
Civil Engineering
Question 51Single Answer
As per IRC (Indian Roads Congress) recommendation, what will be the designed stopping sight distance (in metres) at the vehicle speed of 80 km/h on a rural highway ?
A
120
B
140
C
70
D
60
Question 52Single Answer
No deduction is made in the quantity estimation for plastering work in cement mortar for openings having size up to :
A
0.5 m2
B
1.0 m2
C
3 m2
D
0.75 m2
Question 53Single Answer
What is the height of slump cone mould used for testing the workability of the concrete ?
A
20 cm
B
10 cm
C
30 cm
D
25 cm
Question 54Single Answer
Select the correct option with regard in the following statements (S1, S2) pertaining to pavements .
S1 : Present serviceability index is used for the functional evaluation of pavement surface condition
S2 : Rigid pavements are less affected by temperature variations than flexible pavements
A
Statements S1 is true and Statement S2 is false
B
Both statements S1 and S2 are false
C
Statements S1 is false and Statement S2 is true
D
Both statements S1 and S2 are true
Question 55Single Answer
If the quadrantal bearing of a line AB is S 31'35' E, then its whole circle bearing is equal in :
A
121o25'
B
148o25'
C
58o25'
D
211o25'
Question 56Single Answer
The overflowing sheet of water on a weir is called :
A
creek
B
crest
C
limp
D
nappe
Question 57Single Answer
According to IS 456 - 2000, what is the slump of a medium degree of workability of concrete if planed in heavily reinforced sections like slabs, beams, walls, columns ?
A
10 - 25 mm
B
25 - 50 mm
C
0 - 10 mm
D
50 - 100 mm
Question 58Single Answer
Which of the following is Kharif season in India ?
A
March / April to June / July
B
December / January to April / May
C
May / June to October / November
D
October / November to April / May
Question 59Single Answer
The estimated value of a built - up property at the end of its useful life without dismantled is called :
A
market value
B
book value
C
scrap value
D
salvage value
Question 60Single Answer
The amount of cement required for 100 m2 area, of damp proof course with 2.5 cm thinkness, in with proportion of 1: 2 : 4 (cement : sand : aggregate) will be :
A
2.5 m2
B
0.55 m2
C
1.10 m2
D
0.25 m2
Question 61Single Answer
Select the correct statement related to increasing the carbon content in steel from 0.2 to 0.9 percent .
A
Increasing the carbon content in steel decreases the yield stress and increases the ductility
B
Increasing the carbon content in steel increases the yield stress and reduces the ductility
C
Increasing the carbon content in steel decreases the yield stress and does not affect the ductility
D
Increasing the carbon content in steel does not have any effect on the yield stress or ductility
Question 62Single Answer
Which of the following laws states that pressure or intensity of pressure at a point is static fluid is equal in all directions ?
A
Newton's law
B
Pascal's law
C
Darcy's law
D
Hydrostatic law
Question 63Single Answer
The determination of plasticity index and the percentage by weight of clay mineral finer than 2 µ present in the soil were done for two soil samples A and B. The ratio of plasticity index to the percentage of clay size particle for the samples A and B are given in the table .
Soil sample Ratio of plasticity index to percentage of clay size particle
Sample A Less than 0.75
Sample B Greater than 1.25 The two soil sample A and B are classified as
A
Sample A : Inactive; Sample B : Active
B
Sample A : Active; Sample B : Normal
C
Sample A : Active; Sample B : Inactive
D
Sample A : Normal ; Sample B : Inactive
Question 64Single Answer
Which of the following compounds of cement is responsible for early strength ?
A
C4AF
B
C3S
C
C3A
D
C2A
Question 65Single Answer
According to SP : 27 - 1984, the thickness of slab or RC slab shall be measured to the nearest of :
A
0.0002 m
B
0.005 m
C
0.0001 m
D
0.01 m
Question 66Single Answer
Classify the following pollutants as primary pollutants (PP) and secondary pollutants (SP). Ozone, Carbon monoxide, Particulate matter, photochemical smog, Nitrogen oxides, Aerosol/mist, Hydrocarbons, Perory - Acetyl - Nitrate, Sulphur dioxide.
bulk unit weight of a soil when it is fully saturated
B
saturated bulk unit weight to total void
C
total void to saturated bulk unit weight
D
total void to saturated bulk unit weight
Question 68Single Answer
Identify the test to be conducted for the determination of the modulus of subgrade reaction in pavement design .
A
Plate bearing test
B
Triaxial test
C
CBR test
D
Direct shear test
Question 69Single Answer
In limit state design, the design bond stress for deformed bars (conforming to IS 1786) for M20 concrete mentioned in IS 456 : 2000 is (in N/mm2 units) :
A
1.2
B
1.8
C
1.68
D
1.92
Question 70Single Answer
Which of the following can be considered as a taking off point in road planning in India ?
A
Lucknow plan
B
Delhi plan
C
Bombay plan
D
Nagpur plan
Question 71Single Answer
The following two statements pertain to a simply supported under reinforced concrete beam. Select the correct option with regard is these statements .
1. The failure of the beam takes place due to the yielding of steel .
2. The moment of resistance of the beam is more than that of the balanced section of the beam .
A
Statement 1 is true but Statement 2 is false
B
Statement 1 is false but Statement 2 is true
C
Both statement 1 and 2 are true
D
Both statement 1 and 2 are false
Question 72Single Answer
A continuous beam ABC with span AB = BC = L is shown in the figure. Support A is fixed type, and supports B and C are roller type. The kinematic indeterminacy of the beam is :
A
2
B
3
C
5
D
4
Question 73Single Answer
The soils transported and deposited by a river or a stream care called :
A
aeolian soils
B
alluvial soils
C
lacustrine soils
D
marine soils
Question 74Single Answer
What is the mechanical extra widening required for a two-lane pavement of width 7 m on a horizontal curve of radius 250 m, if the longest wheel base of a vehicle expected on the road is 5 m with a design speed of 70 km/h ?
A
0.155 m
B
0.225 m
C
0.100 m
D
0.552 m
Question 75Single Answer
The following are some of the errors that area associated with a total station survey work. Vertical collimation error, Centering error, Horizontal collimation error, Eccentricity error Categorize the given errors as those due to temporary adjustments (T) and permanent adjustments (P).
A
T : Vertical collimation error, Horizontal collimation error
P : Centering error, Eccentricity error
B
T : Centering error, Horizontal collimation error, Eccentricity error
P : Vertical collimation error
C
T : Eccentricity error, Horizontal collimation error
P : Centering error, Vertical collimation error, Eccentricity error
D
T : Centering error
P : Vertical collimation error, Horizontal collimation error, Eccentricity error
Question 76Single Answer
According to IS 800 : 2007, identify the property which is considered as a mechanical property of structural steel, important in design .
A
Unit mass
B
Maximum percent elongation on a standard gauge length
C
Co - efficient of thermal expansion
D
Poisson ration
Question 77Single Answer
Which of the following methods is NOT used for measuring air content in fresh concrete ?
A
Blaine air permeability method
B
Gravimetric method
C
Pressure method
D
Volumetric method
Question 78Single Answer
Which of the following methods is NOT used for the calculation of depreciation of a structure ?
A
Straight line method
B
Quantity survey method
C
Geometric projection method
D
Declining balance method
Question 79Single Answer
The failure of an over reinforced concrete beam is due to :
A
compression failure
B
mid failure
C
shear failure
D
tension failure
Question 80Single Answer
In which type of estimate is 'Court yard' NOT considered ?
A
Unit rate estimate
B
Plinth area estimate
C
Lump sum estimate
D
Cub rate estimate
Question 81Single Answer
What is runoff in hydrology defined as?
A
Water that infiltrates into the ground
B
Water that flows over the surface into streams
C
Water stored in reservoirs
D
Water evaporated from the surface
Question 82Single Answer
Which factor most significantly affects runoff estimation?
A
Soil permeability
B
Air temperature
C
Wind speed
D
Cloud cover
Question 83Single Answer
What is the primary purpose of runoff estimation in hydrology?
A
Determine groundwater recharge
B
Design hydraulic structures
C
Measure evaporation rates
D
Calculate soil moisture
Question 84Single Answer
Which method is commonly used for runoff estimation in small catchments?
A
Rational method
B
Unit hydrograph method
C
SCS curve number method
D
Muskingum method
Question 85Single Answer
What is the primary source of runoff in a catchment?
A
Groundwater flow
B
Precipitation
C
Evapotranspiration
D
Infiltration
Question 86Single Answer
Which soil type produces the highest runoff?
A
Sandy soil
B
Loamy soil
C
Clayey soil
D
Gravelly soil
Question 87Single Answer
What is the effect of urbanization on runoff?
A
Decreases runoff
B
Increases runoff
C
No effect
D
Reduces infiltration
Question 88Single Answer
Which parameter is critical for the Rational method of runoff estimation?
A
Time of concentration
B
Base flow
C
Evaporation rate
D
Groundwater storage
Question 89Single Answer
What is the primary purpose of the SCS curve number method?
A
Estimate peak discharge
B
Calculate direct runoff
C
Measure base flow
D
Analyze evaporation
Question 90Single Answer
What is the effect of vegetation cover on runoff?
A
Increases runoff
B
Decreases runoff
C
No effect
D
Increases evaporation
Question 91Single Answer
Which factor is used to estimate runoff in the Rational method?
A
Runoff coefficient
B
Curve number
C
Base flow
D
Hydraulic conductivity
Question 92Single Answer
What is the primary purpose of runoff estimation in flood control?
A
Design irrigation systems
B
Predict flood magnitude
C
Measure groundwater recharge
D
Calculate evaporation
Question 93Single Answer
Which method is used for runoff estimation in large catchments?
A
Rational method
B
SCS curve number method
C
Unit hydrograph method
D
Muskingum method
Question 94Single Answer
What is the effect of increasing rainfall intensity on runoff?
A
Decreases runoff
B
Increases runoff
C
No effect
D
Reduces infiltration
Question 95Single Answer
Which soil condition leads to the lowest runoff?
A
Saturated soil
B
Dry sandy soil
C
Compacted clay
D
Urban pavement
Question 96Single Answer
What is the primary purpose of the runoff coefficient in the Rational method?
A
Quantify runoff proportion
B
Measure infiltration
C
Calculate base flow
D
Estimate evaporation
Question 97Single Answer
Which factor is critical for the SCS curve number method?
A
Time of concentration
B
Base flow
C
Curve number
D
Hydraulic gradient
Question 98Single Answer
What is the effect of increasing slope on runoff?
A
Decreases runoff
B
Increases runoff
C
No effect
D
Reduces infiltration
Question 99Single Answer
Which method is used for runoff estimation in ungauged catchments?
A
Rational method
B
Unit hydrograph method
C
SCS curve number method
D
Muskingum method
Question 100Single Answer
What is the primary purpose of runoff estimation in reservoir design?
A
Calculate evaporation
B
Determine inflow volume
C
Measure groundwater recharge
D
Analyze soil moisture
Question 101Single Answer
What is a hydrograph defined as?
A
Graph of rainfall intensity over time
B
Graph of streamflow over time
C
Graph of infiltration rate over time
D
Graph of evaporation over time
Question 102Single Answer
What is the primary purpose of a unit hydrograph?
A
Estimate peak discharge from a unit rainfall
B
Calculate groundwater recharge
C
Measure evaporation rates
D
Analyze soil moisture
Question 103Single Answer
Which component of a hydrograph represents the initial flow before rainfall?
A
Peak discharge
B
Base flow
C
Direct runoff
D
Recession limb
Question 104Single Answer
What is the primary use of a hydrograph in flood forecasting?
A
Predict peak flood discharge
B
Calculate infiltration rates
C
Measure evaporation
D
Estimate soil moisture
Question 105Single Answer
Which parameter is critical for deriving a unit hydrograph?
A
Rainfall duration
B
Evaporation rate
C
Groundwater storage
D
Soil permeability
Question 106Single Answer
What is the effect of increasing catchment area on hydrograph peak discharge?
A
Decreases peak discharge
B
Increases peak discharge
C
No effect
D
Reduces base flow
Question 107Single Answer
Which type of hydrograph is used for a single storm event?
A
Unit hydrograph
B
Synthetic hydrograph
C
Storm hydrograph
D
Annual hydrograph
Question 108Single Answer
What is the primary purpose of the recession limb in a hydrograph?
A
Indicate peak discharge
B
Show decreasing flow after peak
C
Represent base flow
D
Measure infiltration
Question 109Single Answer
Which method is used to derive a unit hydrograph from observed data?
A
Rational method
B
SCS curve number method
C
Convolution method
D
Muskingum method
Question 110Single Answer
What is the effect of urbanization on a hydrograph?
A
Increases time to peak
B
Decreases time to peak
C
No effect
D
Reduces base flow
Question 111Single Answer
What is the primary purpose of a synthetic hydrograph?
A
Estimate hydrograph for ungauged catchments
B
Analyze historical flood data
C
Calculate groundwater recharge
D
Measure evaporation
Question 112Single Answer
Which component of a hydrograph represents surface runoff?
A
Base flow
B
Direct runoff
C
Recession limb
D
Peak discharge
Question 113Single Answer
What is the primary use of a hydrograph in reservoir operation?
A
Determine storage capacity
B
Calculate evaporation rates
C
Measure soil moisture
D
Analyze groundwater recharge
Question 114Single Answer
Which parameter is critical for the shape of a unit hydrograph?
A
Soil permeability
B
Evaporation rate
C
Catchment shape
D
Groundwater storage
Question 115Single Answer
What is the effect of increasing rainfall duration on a hydrograph?
A
Decreases peak discharge
B
Increases peak discharge
C
No effect
D
Reduces base flow
Question 116Single Answer
What is the primary purpose of the rising limb in a hydrograph?
A
Indicate peak discharge
B
Show increasing flow before peak
C
Represent base flow
D
Measure infiltration
Question 117Single Answer
Which method is used to develop a synthetic unit hydrograph?
A
Snyder’s method
B
Rational method
C
SCS curve number method
D
Muskingum method
Question 118Single Answer
What is the effect of vegetation on a hydrograph?
A
Increases time to peak
B
Decreases time to peak
C
No effect
D
Increases peak discharge
Question 119Single Answer
What is the primary use of a hydrograph in bridge design?
A
Measure evaporation
B
Calculate infiltration rates
C
Estimate peak flood discharge
D
Analyze soil moisture
Question 120Single Answer
What is the primary purpose of a unit hydrograph in runoff estimation?
A
Calculate base flow
B
Predict runoff from rainfall
C
Measure evaporation
D
Analyze groundwater recharge
Question 121Single Answer
What is the degree of kinematic indeterminacy for a simply supported beam with an internal hinge?
A
1
B
2
C
3
D
4
Question 122Single Answer
What is the primary structural behavior of a frame under vertical loads?
A
Axial deformation
B
Bending deformation
C
Shear deformation
D
Torsional deformation
Question 123Single Answer
How many plastic hinges are required for collapse in a portal frame with fixed supports?
A
2
B
3
C
4
D
5
Question 124Single Answer
What is the effect of a point load at the crown of a three-hinged arch?
A
Increases horizontal thrust
B
Decreases horizontal thrust
C
No horizontal thrust
D
Causes shear failure
Question 125Single Answer
What is the purpose of special positional reinforcement in a reinforced concrete frame near joints?
A
Resist bending moment
B
Prevent shear failure
C
Increase compressive strength
D
Enhance aesthetic appeal
Question 126Single Answer
What is the degree of static indeterminacy for a two-hinged portal frame?
A
1
B
2
C
3
D
4
Question 127Single Answer
What is the collapse mechanism in a fixed beam under uniform load?
A
One plastic hinge
B
Two plastic hinges
C
Three plastic hinges
D
Four plastic hinges
Question 128Single Answer
What is the primary force in the tie of a tied arch?
A
Compression
B
Tension
C
Shear
D
Bending
Question 129Single Answer
What is the purpose of providing stirrups in a reinforced concrete frame?
A
Resist tensile forces
B
Resist shear forces
C
Increase compressive strength
D
Prevent cracking
Question 130Single Answer
What is the degree of kinematic indeterminacy for a two-hinged portal frame?
A
0
B
1
C
2
D
3
Question 131Single Answer
What is the bending moment at the support of a fixed portal frame under uniform load?
A
Zero
B
Maximum
C
Equal to shear force
D
Indeterminate
Question 132Single Answer
What is the number of plastic hinges required for collapse in a simply supported beam with an internal hinge?
A
1
B
2
C
3
D
4
Question 133Single Answer
What is the effect of unsymmetrical loading on a three-hinged arch?
A
No horizontal thrust
B
Increases horizontal thrust
C
Decreases horizontal thrust
D
Causes torsional failure
Question 134Single Answer
What is the role of bent-up bars in a reinforced concrete frame?
A
Resist tensile forces
B
Resist shear forces
C
Increase compressive strength
D
Prevent buckling
Question 135Single Answer
What is the degree of static indeterminacy for a planar frame with 3 members, 3 joints, and 6 reactions?
A
0
B
1
C
2
D
3
Question 136Single Answer
What is the primary load-carrying mechanism in a fixed arch?
A
Bending
B
Compression
C
Shear
D
Torsion
Question 137Single Answer
What is the collapse load of a propped cantilever beam compared to a simply supported beam?
A
Lower
B
Zero
C
Equal
D
Higher
Question 138Single Answer
What is the degree of kinematic indeterminacy for a fixed beam with an internal hinge?
A
0
B
1
C
2
D
3
Question 139Single Answer
What is the horizontal thrust in a two-hinged arch under uniform load?
A
Zero
B
Maximum at supports
C
Equal to vertical load
D
Indeterminate
Question 140Single Answer
What is the purpose of shear reinforcement in a reinforced concrete frame near supports?
A
Resist bending moment
B
Prevent shear cracks
C
Increase compressive strength
D
Enhance ductility
Question 141Single Answer
What is the degree of static indeterminacy for a simply supported beam with an internal hinge?
A
0
B
1
C
2
D
3
Question 142Single Answer
What is the primary structural behavior of an arch under vertical loads?
A
Axial compression
B
Bending deformation
C
Shear deformation
D
Torsional deformation
Question 143Single Answer
How many plastic hinges are required for collapse in a two-hinged portal frame?
A
2
B
3
C
4
D
5
Question 144Single Answer
What is the effect of temperature drop on a two-hinged arch?
A
Increases vertical deflection
B
Increases horizontal thrust
C
Decreases horizontal thrust
D
No effect
Question 145Single Answer
What is the role of diagonal reinforcement in a reinforced concrete frame near joints?
A
Resist torsional stresses
B
Resist shear stresses
C
Resist axial stresses
D
Resist bending stresses
Question 146Single Answer
What is the degree of static indeterminacy for a planar frame with 7 members, 7 joints, and 9 reactions?
A
0
B
1
C
2
D
3
Question 147Single Answer
What is the bending moment at the crown of a two-hinged parabolic arch under uniform load?
A
Zero
B
Maximum
C
Equal to shear force
D
Indeterminate
Question 148Single Answer
What is the number of plastic hinges required for collapse in a fixed portal frame?
A
2
B
3
C
4
D
5
Question 149Single Answer
What is the primary force in the members of a two-hinged arch?
A
Shear force
B
Axial force
C
Bending moment
D
Torsional force
Question 150Single Answer
What is the purpose of providing additional shear reinforcement in a reinforced concrete frame?