The payment was collected by the hardworking salesman.
A
The hardworking salesman collected the payment.
B
the salesman who worked heard was able to collect the payment.
C
to collect the payment the salesman had to work hard.
D
The hardworking salesman was able to collect the payment.
Question 4Single Answer
I had to stop all my work to complete this project.
A
All other work had to be stopped to complete this project by me
B
For completing this project all other work must be stopped
C
For completing this project I had to stop all my work
D
To complete this project all other work had been stopped by me
Question 5Single Answer
They have published the names of all the successful candidates.
A
The candidates who have succeeded their names they had published.
B
The names of all the successful candidates have been published by them
C
The candidates who have succeeded their names have been published by them.
D
The names of all the successful candidate were published by them.
Question 6Single Answer
The online shopping site lowered the prices.
A
Lowering of the prices was done by the online shopping site
B
The prices were lowered by the online shopping site
C
The prices had been lowered by the online shopping site
D
The prices have been lowered by the online shopping site
Question 7Single Answer
Who taught you to drive a truck ?
A
To drive a truck by whom were you taught?
B
Driving a truck by who were you taught?
C
Driving a truck by who were you being taught?
D
By whom were you taught to drive a truck?
Question 8Single Answer
We shall invite Suresh.
A
Suresh would be invited by us
B
Suresh would have been invited by us
C
Suresh will be invited by us
D
Suresh will have been invited by us
Question 9Single Answer
Dark clouds have overcast the evening sky.
A
By the dark clouds the evening sky was overcast.
B
The evening sky has been overcast by the dark clouds.
C
Dark clouds overcastted the evening sky.
D
The sky of the evening was overcasted by dark clouds.
Question 10Single Answer
The partners will celebrate their triumph tomorrow.
A
The triumph would be celebrated by the partners a day before
B
The triumph would be celebrated by the partners a day after
C
The triumph would have been celebrated by the partners a day after
D
The triumph will have been celebrated by the partners tomorrow
Question 11Single Answer
Why did break the vase?
A
why is the vase broken by him
B
why was the vase broken by him
C
why had been the vase broken by him
D
why has been the vase broken by him
Question 12Single Answer
Mariam was writing a note to her boss.
A
A note was written to her boss by Mariam
B
A note was wrote by Mariam to her boss
C
A note was being written by Mariam to her boss
D
A note was written by Mariam to her boss
Question 13Single Answer
The baby really enjoys that music.
A
That music was really enjoyed by the baby.
B
That music was really being enjoyed by the baby.
C
That music is really enjoyed by the baby.
D
This music was really enjoyed by the baby.
Question 14Single Answer
The weather disrupted the final match.
A
The final match has been disrupted by the weather.
B
The final match had been disrupted by the weather.
C
The final match was disrupted by the weather.
D
The final match was being disrupted by the weather.
Question 15Single Answer
The management committee is required to publish a report every year.
A
report would be published by the management committee every year.
B
A report would have been published by the management committee every year.
C
A report requires to be published by the management committee every year.
D
Every year the report would be published by the management committee.
Question 16Single Answer
Preeti ran the race in record time.
A
In record time Preeti ran the race.
B
The race was run by Preeti in record time
C
The race was being run by Preeti in record time
D
The race had been run by Preeti in record time
Question 17Single Answer
I shall have written the full thesis by December
A
By December I shall have wrote the full thesis.
B
The full thesis will have been written by me by December.
C
The full Thesis will be wrote by me by December
D
By December the full thesis must have been wrote by me.
Question 18Single Answer
One must keep one’s promises.
A
One’s promises must be kept by one.
B
One’s promises had to be kept.
C
Promises must be kept.
D
Promises have to be kept by one.
Question 19Single Answer
I read the story in one night.
A
The story had been read by me in one night.
B
The story has been read by me in one night
C
n one night the story has been read by me.
D
the story was read by me in one night
Question 20Single Answer
We must take care of the old.
A
Those who are old need to be taken care of by us.
B
The old must be taken care of by us.
C
Those who are old need care by us
D
The old should be taken care of by us.
Question 21Single Answer
My father generously donated money to the church.
A
Money is generously being donated to te church by my father.
B
Money has been generously donated to the church by my father.
C
Money had been generously donated to the church by my father.
D
Money was generously donated to the church by my father.
Question 22Single Answer
We will send you your laboratory reports as soon as they are ready
A
you would be sent your laboratory reports as soon as they will be ready.
B
Your laboratory reports will be sent to you as soon as they are ready.
C
You would be send your laboratory reports as soon as they will be ready.
D
Your laboratory reports should be sent to you as soon as they will be ready.
Question 23Single Answer
I saw the master conducting the orchestra.
A
I saw that the orchestra was being conducted by the master.
B
I saw the orchestra being conducted by te master
C
The master was seen conducting the orchestra by me.
D
The master was conducting the orchestra and I saw that.
Question 24Single Answer
The dog is being fed by us.
A
We fed the dog.
B
We have had been feeding the dog.
C
We are feeding the dog
D
We had been feeding the dog
Question 25Single Answer
When did Rohit return my bike?
A
When was my bike returned by Rohit?
B
When was it that Rohit returned my bike?
C
Rohit returned my bike when?
D
When did my bike come back from Rohit?
Question 26Single Answer
They are going to watch a drama tomorrow.
A
A drama is going to be watched by them tomorrow.
B
A drama will be watched by them tomorrow.
C
A drama will be watched by them tomorrow.
D
A drama was going to be watched by them tomorrow.
Tomorrow the drama is going to be watched by them.
Question 27Single Answer
The event manager is making all the reservations.
A
All the reservations would be made by the event manager.
B
All the reservations are being made by the event manager.
C
All the reservations would have been made by the event manager.
D
All the reservations will have been made by the event manager.
Question 28Single Answer
The Marathas surrendered their fort to the Mughals after the war.
A
After the war the Marathas had to surrender their fort to the Mughals.
B
The Mughals after the war took fort surrendered by the Marathas.
C
Their fort was surrendered by the Marathas to the Mughals after the war
D
the Marathas after the war surrendered their fort to the Mughals.
Question 29Single Answer
Mother filled dark filtered coffee in the cup.
A
The cup was filled with dark filtered coffee by mother.
B
Mother filled in the cup coffee which was dark and filtered coffee.
C
The cup was being by mother with dark filtered coffee.
D
The filtered coffee which was dark was filled into the cup by mother.
Question 30Single Answer
The most useful gift of my wedding was given to me by my aunt.
A
My aunt gave me the most useful gift of my wedding.
B
My aunt had given me the most useful gift of my wedding.
C
The gift which has been most useful has been given to me by my aunt.
D
My aunt has given me the most useful gift of my wedding.
Question 31Single Answer
The painting had not been painted by the famous painter.
A
The panting had never been painted the painting.
B
The painter who was famous not had painted the painting.
C
The famous painter had not painted te painting
D
The famous painter could not have painted the painting.
Question 32Single Answer
The Kangaroo carried her baby in her pouch.
A
The baby is carried by the kangaroo in er pouch.
B
The is being carried by the kangaroo in her pouch
C
The baby had been carried by the kangaroo in her pouch.
D
The baby was carried by the kangaroo in her pouch.
Question 33Single Answer
The painters painted the entire building.
A
The entire building had been painted by the painters.
B
The painters had an entire building painted.
C
The entire building was painted by the painters.
D
The entire building has been painted by the painters.
Question 34Single Answer
The office boy vacuums and dusts the office every morning.
A
Every morning the office had been vacuumed and dusted by the office boy.
B
Every morning the office is vacuumed and dusted by the office boy.
C
Every morning the office has been vacuumed and dusted by the office boy.
D
Every morning the office has been vacuumed
Question 35Single Answer
I will wash the car every Sunday.
A
The car would be washed by me every Sunday.
B
The car will be washed by me every Sunday.
C
Every Sunday the car would be washed by me.
D
The car will have been washed by me every Sunday.
Civil Engineering
Question 36Single Answer
Consider the following statements :
1. There will be no defects in select grade timbers.
2. The codal values for strength of grade-II timer without defects may be reduced by 37.5%.
3. For timber used as columns, the permissible stress in ungraded timbers is adopted with a multiplying factor of 0.50.
4. In case of wind force and earthquakes, a modification factor of 1.33 is adopted. Which of the above statements are correct ?
A
1 and 3 only
B
1 and 4 only
C
2 and 4 only
D
2 and 3 only
Question 37Single Answer
Consider the following statements regarding timber :
1. The strength of timber increases by Kiln seasoning.
2. Cutting of wood is to be done prior to treatment.
3. Water seasoning is good for prevention of warping.
4. ASCU treatment enhances the strength of wood. Which of the above statements are correct ?
A
1, 2 and 3 only
B
2, 3 and 4 only
C
1, 3 and 4 only
D
1, 2, 3 and 4
Question 38Single Answer
Gase(s) emitted during rotting or decomposition of timber is /are mainly
A
Methane and Hydrogen
B
Hydrogen Sulphide
C
Carbonic acid and Hydrogen
D
Ammonia
Question 39Single Answer
Efflorescence of bricks is due to
A
Excessive burning of bricks
B
High silt content in brick clay
C
High porosity of bricks
D
Soluble salts present in parent clay
Question 40Single Answer
Disintegration of bricks masonry walls is primarily due to
1. Efflorescence
2. Magnesium sulphate in brick
3. Calcined clay admixtures
4. Kankar nodules
Which of the a above statements are correct ?
A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 41Single Answer
Consider the following test :
1. Transverse strength test
2. Water absorption test
3. Impact test
4. Breaking strength test
Which of the above are relevant to testing of tiles ?
A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 42Single Answer
Which of the following statements is/are correct regarding the strength of cement ?
1. Particle sizes less than 3 m increases the viscous nature of the cement.
2. Finer particles in cement can be replaced by fly-ash to improve the strength.
A
1 only
B
2 only
C
Both 1 and 2
D
Neither 1 nor 2
Question 43Single Answer
The constituent compound in Portland cement which reacts immediately with water, and also sets earliest, is
A
Tricalcium silicate
B
Dicalcium silicate
C
Tricalcium aluminate
D
Tetracalcium aluminoferrite
Question 44Single Answer
Which of the following statements are correct with regard to cement mortar ?
1. Workability of cement mortar can be improved by addition of lime.
2. Fly-ash cement is economical in plastering jobs.
3. Addition of saw dust improves workability.
4. Sand in mortar can be replaced by finely crushed fire bricks.
A
1, 2, 3 and 4
B
1, 2 and 3 only
C
3 and 4 only
D
1, 2 and 4 only
Question 45Single Answer
In a concrete mix of proportion 1 : 3 : 6, the actual quantity of sand, which is judged to have undergone 15% bulking, per unit volume of cement, will be
A
3.00
B
3.45
C
4.50
D
6.00
Question 46Single Answer
Which method of curing of concrete is recommendable for rapid gain of strength of concrete ?
A
Sprinkling water
B
Membrane curing
C
High-pressure steam curing
D
Infrared radiation curing
Question 47Single Answer
Which of the following is appropriate as simple field method for assesing consistency of concrete ?
A
Compacting factor
B
Slump test
C
Vee-Bee test
D
Kelly Ball test
Question 48Single Answer
Which of the following are relatable to Autoclaved Aerated Concrete ?
1. Light weight
2. Strong
3 Inorganic
4. Nontoxic
A
1, 2 and 3 only
B
1, 2 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 49Single Answer
The workability of concrete becomes more reliable depending on
1. Aggregate-cement ratio
2. Time of transit
3. Grading of the aggregate
A
1 only
B
2 only
C
3 only
D
1, 2 and 3
Question 50Single Answer
Which of the following statements are correct for stresses acting on mutually perpendicular faces of a plane element ?
1. The sum of the normal stresses in mutually perpendicular planes is equal to the sum of the principal stresses.
2. The shearing stresses in two mutually perpendicular planes are equal in magnitude and direction.
3. Maximum shear stress is half of the difference between principal stresses.
A
1, 2 and 3 only
B
1 and 2 only
C
2 and 3 only
D
1 and 3 only
Important Questions Package
CEIL Inspection Engineer Exam Online Question Bank Package
Buy CEIL Inspection Engineer Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in CEIL Inspection Engineer question bank 2026 in Online, PDF & Print study material.
+ Free Monthly Current Affairs, GK & more PDF Download
Sr.
Package Name
Amount
1.
CEIL Inspection Engineer & Safety Officer Exam Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390[₹600]
2.
CEIL Inspection Engineer & Safety Officer Exam Question Bank Book - Hindi
Description : 1000 Question with Answer (Printed Material)
₹450[₹800]
3.
CEIL Inspection Engineer & Safety Officer Exam - English
Description : 2500 Question with Answer.
₹271[₹500]
4.
CEIL Inspection Engineer & Safety Officer Exam - Hindi
Description : 2500 Question with Answer.
₹271[₹500]
Civil Engineering
Question 51Single Answer
Which of the following statements are correct?
1. Strain in the direction of applied stress is known as longitudinal strain.
2. Tensile stress results in tensile strain in linear and lateral directions.
3. Strains in all directions perpendicular to the applied stress are known as lateral strain. 4. Ratio of change in volume to original volume is known as volumetric strain.
A
1, 2 and 3 only
B
1, 3 and 4 only
C
3 and 4 only
D
1, 2, 3 and 4
Question 52Single Answer
In the cross-section of a timber, cambium layer can occur in
A
Inner Bark and Sap Wood
B
Pith and Heart Wood
C
Sap Wood and Heart Wood
D
Outer Bark and Sap Wood
Question 53Single Answer
Consider the following statements :
1. In the infinitesimal strain theory, dilatation is taken as an invariant.
2. Dilatation is not proportional to the algebraic sum of all normal stresses.
3. The shearing modulus is always less than the elastic modulus.
Which of the above statements is/are correct ?
A
1 only
B
1 and 2 only
C
2 only
D
1, 2 and 3
Question 54Single Answer
Which one of the following represents constitutive relationship ?
A
Vertical displacements in a structure
B
Rotational displacements in a structure
C
System of forces in equilibrium
D
Stress-strain behavior of a material
Question 55Single Answer
Principal stresses at a point are 80 N/mm2 and 40 N/mm2, both tensile. The yield stress in simple tension for this material is 200 N/mm2. The values of factors of safety according to maximum principal stress theory and maximum shear stress theory, respectively, are
A
2.5 and 2.5
B
2.5 and 5
C
5 and 1.67
D
6 and 2.50
Question 56Single Answer
The principal stresses at a point are 2 (tensile) and (compressive), and the stress at elastic limit for the material in simple tension is 210 N/mm2. According to maximum shear strain theory, the value of at failure is
A
70 N/mm2
B
105 N/mm2
C
140 N/mm2
D
210 N/mm2
Question 57Single Answer
Which of the following statements are correct ?
1. Cranes are employable in moving and/or hoisting loads.
2. With the use of dipper and stick, power shovels can be used as hoes.
3. Ovedrive for higher speeds is a facility often used comfortably in the working of a tractor.
4. Clam shells are less desirable than draglines if the material is water-saturated.
A
1 and 4 only
B
1 and 2 only
C
2 and 3 only
D
3 and 4 only
Question 58Single Answer
Two similar bars of Steel and Aluminium are heated to a same temperature. Forces are applied at the ends of the bars to maintain their lengths unaltered. If the ratio of Young’s moduli of Steel and Aluminium is 3, and the ratio of the coefficients of thermal expansion of Steel to that of aluminium is 0.5, what is the stress on the Aluminium bar if the stress on the Steel bar is 100 MPa ?
A
16.7 MPa
B
66.7 MPa
C
136.7 MPa
D
150.0 MPa
Question 59Single Answer
A structural steel beam has an unsymmetrical I-cross-section. The overall depth of the beam is 200 mm. The flange stresses at the top and bottom are 120 N/mm2 and 80 N/mm2, respectively. The depth of the natural axis from the top of the beam will be
A
120 mm
B
100 mm
C
80 mm
D
60 mm
Question 60Single Answer
In the analysis of beams subjected to loads, the point with Nil Bending Moment can be a
1. Point of Contraflexure
2. Point of Maximum Shear Force
3. Point of Inflection
Which of the above statements is/are correct ?
A
1 only
B
2 only
C
3 only
D
1, 2 and 3
Question 61Single Answer
A tractor has a permissible loaded speed of 200 m/minute, which can increase by 25% when the load is removed/deposited. Generally, it is operated at 80% of the permissible speed (loaded unloaded). It works at a location where haul distance is 120 m. Rest allowance per round-trip is taken as 50 seconds on an average. Fixed time per trip, for loading and unloading and turnaround, etc., is 30 seconds. What is its effective cycle time?
A
157 seconds
B
161 seconds
C
173 seconds
D
182 seconds
Question 62Single Answer
The purpose of lateral ties in a short RC column is to
A
Avoid buckling of longitudinal bars
B
Facilitate compaction of concrete
C
Increase the load carrying capacity of the column
D
Facilitate construction
Question 63Single Answer
When a two-hinged parabolic arch is subjected to a rise in ambient temperature, the horizontal thrust at the support will
A
Increase
B
Decrease
C
Remain same
D
Increase or decrease depending on the span
Question 64Single Answer
In the slope-deflection equations, deformations are considered to be caused by
A
Shear forces and bending moments only
B
Axial forces, shear forces and bending moments
C
Axial forces and bending moments only
D
Bending moments only
Question 65Single Answer
The maximum bending moment caused by a set of concentrated moving loads is
A
Always at the midpoint of span
B
Between the midpoint and concentrated load next to the midpoint of the span
C
Not definable
D
Always under a load close to the centroid of the set of loads
Question 66Single Answer
Force method of analysis of a structure is particularly preferred when
1. The degrees of freedom of the structure become large
2. The structure has less number of static, and more number of kinematic, indeterminacies
3. The structure has more numbers of static, and less numbers of kinematic, indeterminacies
A
1 only
B
2 only
C
3 only
D
1, 2 and 3
Question 67Single Answer
Stiffness matrix method is the category of
1. Compatibility method
2. Displacement method
3. Force method
4. Equilibrium method
A
1 and 3 only
B
1 and 4 only
C
2 and 3 only
D
2 and 4 only
Question 68Single Answer
Muller-Breslau Principal for obtaining influence lines is applicable to
1. Statically determinate beams and frame
2. Statically indeterminate structures, the material of which is elastic, and follows Hooke’s law.
3. Any statically indeterminate structure
A
1 and 2 only
B
1 only
C
2 only
D
1 and 3 only
Question 69Single Answer
The plastic neutral axis
1. Divides the given section into two equal halves
2. Divides the given section into two unequal parts
3. Lies on the centroidal axis of the section
A
1 only
B
2 only
C
3 only
D
2 and 3 only
Question 70Single Answer
The plastic moment capacity MP is
A
Less than the yield moment
B
Equal to the yield moment
C
Greater than the yield moment
D
Dependent on section dimensions
Question 71Single Answer
Web crippling is caused by
A
Excessive bending moment
B
Failure of web under point loads
C
Width of flanges
D
Column action of web
Question 72Single Answer
The block shear failure of a bolted joint in tension occurs because of
1. Use of higher shear strength bolts
2. Use of paltes with higher bearing strength
A
1 only
B
2 only
C
Both 1 and 2
D
Neithter 1 nor 2
Question 73Single Answer
As per IS code, the maximum longitudinal pitch allowed in bolted joints of tension members is nominally
A
12 times the thickness of the plate
B
12 times the diameter of the bolt
C
16 times the thickness of the plate
D
16 times the diameter of the bolt
Question 74Single Answer
ISMB 100 (rx = 40 mm, ry = 10 mm) has been used as a column in a industrial shed. Along the minor axis, the the column has restraints in the form of purlins at 1.0 m intervals. Effective length factor along major and minor axes are 1.2 and 1.0, respectively. If the slenderness ratio is restricted to 120, the maximum column height will be
A
1.0 m
B
2.4 m
C
4.0 m
D
4.8 m
Question 75Single Answer
As per IS 800 – 2007, the permitted slenderness ratio for a bracing member in case of hangers shall be
A
140
B
145
C
150
D
160
Question 76Single Answer
A rectangular beam of depth d is under bending. Load has been gradually increased when the top fibre has obtained five times the strain at the first yield. What depth of the beam will still respond by elastic conditions?
A
0.16 d
B
0.20 d
C
0.25 d
D
0.40
Question 77Single Answer
The ultimate moment capacity of a mild steel section is usually
A
Equal to the plastic moment capacity
B
More than the yield moment capacity
C
Let than the yield moment capacity
D
More than the plastic moment capacity
Question 78Single Answer
The portal bracing in a truss-bridge is used to
A
Transfer load from top of end posts to bearings
B
Maintain the rectangular shape of the bridge cross-section
C
Stiffen the structure laterally
D
Prevent the buckling of top chord under side sway
Question 79Single Answer
Consider the following cases in the design of reinforced concrete members in flexure:
1. Over-reinforced section
2. Tension failure
3. Compression failure
4. Under-reinforced section
Which of the above cases are considered for safe design of R.C members in flexure?
A
1 and 2 only
B
2 and 4 only
C
3 and 4 only
D
1 and 3 only
Question 80Single Answer
The bond between steel and concrete is mainly due to
1. Mechanical resistance
2. Pure adhesive resistance
3. Frictional resistance
A
1 and 2 only
B
1 and 3 only
C
2 and 3 only
D
1, 2 and 3
Question 81Single Answer
The carbonation process is demonstrated more by
A
Atmospheric corrosion
B
Chloride corrosion
C
Stress corrosion
D
Hydrogen embrittlement
Question 82Single Answer
When a sprially reinforced short column is loaded axially, the concrete inside the core is subjected to
A
Bending and compression
B
Biaxial compression
C
Triaxial compression
D
Uniaxial compression
Question 83Single Answer
In a reinforced concrete section, shear stress distribution is diagrammatically
A
Wholly Parabolic
B
Wholly Rectangular
C
Parabolic above NA and Rectangular below NA
D
Rectangular above NA and Parabolic below NA
Question 84Single Answer
As per IS 456 – 2000, the maximum permissible shear stress, TCmax' is based on
A
Diagonal tension failure
B
Diagonal compression failure
C
Flexural tension failure
D
Flexural compression failure
Question 85Single Answer
Footings shall be designed to sustain the
1. Applied loads
2. Moments and forces under relatable loading conditions
3. Induced reactions
A
1and 2 only
B
1 and 3 only
C
2 and 3 only
D
1, 2 and 3
Mechanical Engineering
Question 86Single Answer
A fin will be more effective when Bio number is
A
Greater than 1
B
Equal to 1
C
Between 1 and 3
4 4
D
Less than 1
Question 87Single Answer
A tank of length, breadth and height in the ratio of 2:1:2 is full of water. The ratio of hydrostatic force at the bottom to that at any larger vertical surface is
A
1
B
2
C
3
D
4
Question 88Single Answer
Which of the following fluids exhibit a certain shear stress at zero shear strain rate followed by a straight line relationship between shear stress and shear strain rate?
A
Newtonian fluid
B
Ideal Bingham plastic fluids
C
Pseudo-plastic fluids
D
Dilatent fluids
Question 89Single Answer
What is the specific gravity of a marble stone, which weighs 400N in air, and 200N in water? (g=10m/s2)
A
8
B
6
C
4
D
2
Question 90Single Answer
What is the intensity of pressure in the following SI units, when specific gravity of mercury is 13.6 and the intensity of pressure is 400KPa ?
A
0.3 bar or 4.077m of water or 0.29 mm of Hg
B
4 bar or 5.077m of water or 0.399 mm of Hg
C
0.3 bar or 5.077m of water or 0.599 mm of Hg
D
4 bar or 4.077m of water or 0.299 mm of Hg
Question 91Single Answer
Consider the following statements:
1.If a small upward displacement is given to a floating body, it results in the reduction of the buoyant force acting on the body
2.A slight horizontal displacement does not change either the magnitude or the location of the buoyant force
Which of the above statements is/are correct?
A
Both 1 and 2
B
1 only
C
2 only
D
Neither 1 nor 2
Question 92Single Answer
State whether following flow field is physically possible?
A
Possible for steady, incompressible flow
B
Possible for unsteady, incompressible flow
C
Possible for steady, compressible flow
D
Not Possible
Question 93Single Answer
In a differential manometer, a head of 0.5 m of fluid A in limb 1 is found to balance a head of 0.3 m of fluid B in limb 2. The atmospheric pressure is 760 mm of mercury. The ratio of specific gravities of A to B is
A
0.25
B
0.26
C
2
D
4
Question 94Single Answer
A Reversed Carnot Engine removes 50 kW from a heat sink. The temperature of the heat sink is 250 K and the temperature of the heat reservoir is 300 K. The power required of the engine is
A
10 kW
B
20 kW
C
30 kW
D
50 kW
Question 95Single Answer
On which of the following just in time manufacturing philosophy emphasizes ?
A
man power
B
profit
C
inventory
D
manufacturing
Question 96Single Answer
In a stream line steady flow, two points A and B on a stream line are 1m apart and the flow velocity varies uniformly from 2m/s to 5m/s. What is the acceleration of fluid at B?
A
3 m/s2
B
6 m/s2
C
9 m/s2
D
15 m/s2
Question 97Single Answer
The stream function is given by Ψ = 3xy, then the velocity at the point (2,3) is
A
9
B
-6
C
117
D
10.8
Question 98Single Answer
The boundary layer thickness at a given distance from the leading edge of a flat plate is
A
More for lighter fluid
B
More for denser fluid
C
Less for denser fluid
D
Less for lighter fluid
Question 99Single Answer
In a laminar flow through a circular pipe, the discharge varies
A
Linearly with fluid density
B
Inversely with pressure drop
C
Directly as square of pipe radius
D
Inversely with fluid velocity
Question 100Single Answer
A fluid is flowing over a flat plate. At distance of 8 cm from the leading edge, the Reynolds number is found to be 25600. The thickness of the boundary layer at this point is
A
1.5mm
B
2.5mm
C
4.0mm
D
5.0mm
Question 101Single Answer
Air is flowing over a flat plate with a free stream velocity of 24 m/s, and its kinematic viscosity is 72 ×10-6m2/s. If at a particular point, the Reynolds number is 30000, its location from the leading edge is
A
0.05m
B
0.07m
C
0.08m
D
0.09m
Question 102Single Answer
In a refrigerator, the evaporator and condenser coil temperatures are –33°C and 27°C, respectively. Assuming that the maximum COP is realized, the required power input for a refrigerating effect of 4 kW is
A
8 kW
B
4 kW
C
2 kW
D
1 kW
Question 103Single Answer
In a hydraulic coupling
A
The magnitudes of input and output torques are equal
B
The magnitudes of input torque is greater than output torque
C
The magnitudes of input torque is less than output torque
D
The magnitudes of input torque is negligible as compared to output torque
Question 104Single Answer
Consider the following statements:
1.The wheel can be operated freely in air
2.Pressure at the exit of the nozzle is atmospheric
3.Pressure does not vary along the moving vanes
4.Change the direction of momentum imparts thrust over moving vanes Which of the following statements are applied to impulse turbine?
A
1,2 and 3 only
B
1,2 and 4 only
C
3 and 4 only
D
1,2, 3 and 4
Question 105Single Answer
A water jet 0.0015m2in area issues from a nozzle with 15 m/s velocity. It is made to impinge perpendicular on to a plate that moves away from the jet with a velocity of 5 m/s. The force on the plate due to this impact is
A
150 N
B
1470 N
C
340 N
D
900 N
Question 106Single Answer
Consider the following statements with regard to hydraulic turbines:
1.Kaplan turbines are most efficient at part load operations.
2.If n is the number of jets in a Pelton turbine, then the specific speed is proportional to n2.
3.The flow ratio of Francis turbines are in the range of 0.1 – 0.3.
Which of the above statements is/are correct?
A
1,2 and 3
B
1 and 2 only
C
1 and 3 only
D
2 and 3 only
Question 107Single Answer
Which of the following is a Vector quantity ?
A
Energy
B
Mass
C
Momentum
D
Angle
Question 108Single Answer
Bernoulli’s equation is applicable between any two points located in
A
Rotational flow of an incompressible fluid
B
Irrotational flow of compressible or incompressible fluid
C
Steady, rotational flow of an incompressible fluid
D
Steady, irrotational flow of an incompressible fluid
Question 109Single Answer
Water flows through a smooth circular pipe of diameter D and length L because of a pressure difference ΔP across the length. The volume flow rate is Q and the flow is turbulent with Reynolds number 105. If the pressure difference is increased to 4ΔP the volume flow rate will be
A
2Q
B
A little more than 2Q
C
A little less than 2Q
D
4Q
Question 110Single Answer
Heat is lost from a 100 mm diameter steam pipe placed horizontally in ambient air at 30°C. If the Nusselt number is 25 and the thermal conductivity of the air is 0.03 W/m K, then the heat transfer coefficient will be
A
7.5 W/m2K
B
15 W/m2K
C
25 W/m2K
D
35 W/m2K
Question 111Single Answer
For laminar flow through a round pipe, the shear stress
A
Remains constant over the cross-section
B
Varies linearly with the radial distance
C
Must be zero at all point
D
Varies parabolically with radial distance
Question 112Single Answer
Percentage clongation during tensile test is indicative of
A
Creep
B
Malleability
C
Ductility
D
Elasticity in the metal
Question 113Single Answer
Which of the above statements is not correct in the context of laminar flow through a pipeline?
A
Shear stress is zero at the center and varies linearly with pipe radius
B
Head loss is proportional to square of the average flow velocity
C
The friction factor varies inversely with flow Reynolds number
D
No dispersion of die injected into the flow stream
Question 114Single Answer
Laminar flow between closely spaced parallel plates is governed by the consideration of which one of the following pair of forces?
A
Pressure and inertial forces
B
Gravity and inertial forces
C
Viscous and inertial forces
D
Pressure and inertial forces
Question 115Single Answer
Formation and collapse of vapour bubbles are believed to be the root cause for cavitation in hydraulic turbines. Most favorable condition for the formation of bubbles is set in the turbine at
A
Penstock/nozzl
B
Guide vanes/Inlet of the runner
C
Vanes receiving impact of jet
D
Outlet of the runner/Entrance of the draft tube
Question 116Single Answer
For fully developed laminar flow through a circular pipe with Reynolds number Rethe friction factor is
A
Inversely proportional to Re
B
Proportional to Re
C
Proportional to square of Re
D
Independent of Re
Question 117Single Answer
The ratio of power outlet of the pump to the power input to the pump is known as
A
Mechanical efficiency
B
Static efficiency
C
Overall efficiency
D
Manometric efficiency
Question 118Single Answer
A pump is defined as a device which converts
A
Hydraulic energy into Mechanical energy
B
Mechanical energy into Hydraulic energy
C
Kinetic energy into Mechanical energy
D
None of the above
Question 119Single Answer
The specific speed of a pump is defined as the speed of the unit of such a size that is
A
Delivers the unit discharge at unit head
B
Requires unit power to develop unit head
C
Delivers the unit discharge at unit power
D
Produces unit power with unit head available
Question 120Single Answer
Negative slip occurs in reciprocating pumps, when delivery pipe is
A
Long and suction pipe is short and pump is running atlow speed
B
Long and suction pipe is short and pump is running at high speed
C
Short and suction pipe is long and pump is running at low speed
D
Short and suction pipe is long and pump is running at high speed
Question 121Single Answer
The pressure inside a soap bubble of 50 mm diameter is 25 N/m2 above the atmospheric pressure. The surface tension in soap film would be
A
0.156 N/m
B
0.313 N/m
C
0.624 N/m
D
0.078 N/m
Question 122Single Answer
A Newtonian fluid is one which
A
Is viscous but incompressible
B
Has a linear relationship between the shear stress and the rate of angular deflection
C
Exhibits an increase in viscosity with increasing rate of deformation
D
Exhibits a decrease in viscosity with increasing rate of deformation
Question 123Single Answer
Unlike the viscosity of fluids, the viscosity of gases increases with increasing temperature. This is due to
A
Increased cohesive force between the molecule
B
Increased momentum transfer in the molecules
C
Decreased momentum transfer in the molecules
D
Increase in both cohesive force and momentum transfer
Question 124Single Answer
Manometer is a device used for measuring
A
Velocity at a point in a fluid
B
Pressure at a point in a fluid
C
Discharge of a fluid
D
None of the above
Question 125Single Answer
When a dolphin glides through air, it experiences an external pressure of 0.75 m of mercury. The absolute pressure on dolphin when it is 5m below the free surface of the water is
A
0.10 N/m2
B
0.5 N/m2
C
1.0 N/m2
D
0.15 N/m2
Question 126Single Answer
Which of the above statements is correct?
A
For a floating body, the stable equilibrium condition exists when position of metacenter remains higher than the center of gravity of the body
B
For a floating body, the stable equilibrium condition exists when position of metacenter remains lower than the center of gravity of the body
C
For a floating body, the neutral equilibrium condition exists when position of metacenter remains higher than the center of gravity of the body
D
For a floating body, the unstable equilibrium condition exists when position of metacenter remains higher than the center of gravity of the body
Question 127Single Answer
A wall of 0.6m thickness has normal area of 1.5 m2 and is made up of material of thermal conductivity 0.4 W/mK. If the temperature on the two sides of the wall are 800°C and 1000°C, the thermal resistance of the wall is
A
1.8 K/W
B
1.8 W/K
C
1 K/W
D
1 W/K
Question 128Single Answer
A flownet is a graphical representation of streamlines and euqipotnetial lines such as these lines
A
Intersect each other at various different angles forming irregular shaped nets
B
Intersect each other orthogonally forming curvilinearsquares
C
Indicate the direction but not magnitude of vector
D
Indicate the direction and magnitude of vector
Question 129Single Answer
Which of the above statements is correct for the velocity of potential?
A
Existence of velocity potential is an indication of irrotational nature of the flow
B
The velocity potential automatically satisfies the continuity equation
C
Velocity potential can be defined only for 2-dimensional flow
D
All of the above
Question 130Single Answer
Angle of diverging portion of the venturimeter is limited to 7°, because:
1.Flow decelerates in the diverging portion and pressure increases in the downstream direction. Hence, the fluid experience an adverse pressure gradient, if the divergence angle is large.
2 .Flow separation takes place due to adverse pressure gradient when divergence angle is large.
3 .If the divergence angle is large, a negative pressure is created at the throat which obstructs the flow of fluid.
Which of the above reasons are correct?
A
1, 2 and 3
B
1 and 2 only
C
1 and 3 only
D
2 and 3 only
Question 131Single Answer
A gas is flowing through an insulated nozzle. If the inlet velocity of gas is negligible and there is an enthalpy drop of 45kJ/kg, the velocity of gas leaving the nozzle is
A
100m/s
B
200m/s
C
300m/s
D
350m/s
Question 132Single Answer
Which of the above statements are correct for turbo-prop powered aircrafts?
1 .The propulsion efficiency of turbo-prop is higher than that of turbo-jet and rockets for low speeds up to about 800km/hr.
2.For the same thrust the turbine in the turbo prop aircraft is smaller than in the turbo-jet aircraft.
3.For the turbo-prop the flight velocity cannot exceed the jet velocity.
A
1,2 and 3
B
1 and 2 only
C
2 and 3 only
D
1 and 3 only
Question 133Single Answer
If absolute jet exit velocity from a jet engine is 2800m/s and forward flight velocity is 1400m/s then propulsive efficiency is
A
33.33%
B
40%
C
66.66%
D
90%
Question 134Single Answer
An air-breathing aircraft is flying at an altitude where the air density is half the value at ground level. With reference to the ground level, the air fuel ratio at this altitude will be
A
1
2
B
1
C
2
D
4
Question 135Single Answer
Which of the above statements are correct for rockets?
1.Unlike the turbo-jet aircraft, in rockets the flight velocity can exceed the jet velocity.
2.In rockets gases having lower molecular weight increase the specific thrust.
3.In rockets the gases are expanded in the nozzle up to the atmospheric pressure.
A
1,2 and 3
B
1 and 2 only
C
2 and 3 only
D
1 and 3 only
Aptitude
Question 136Single Answer
The cash difference between the selling prices of an article at a profit of 4% and 6% is Rs. 3. The ratio of the two selling prices is:__________ ?
A
51:52
B
52:53
C
51:53
D
52:55
Question 137Single Answer
Which of the following numbers is irrational ?
A
√49
B
0.125
C
√2
D
22/7
Question 138Single Answer
356 x 936 – 356 x 836 = ?
A
35600
B
34500
C
9630
D
93600
Question 139Single Answer
Arrange in descending order: 5/8, 7/10, 3/4
A
3/4 > 7/10 > 5/8
B
7/10 > 3/4 > 5/8
C
3/4 > 5/8 > 7/10
D
5/8 > 7/10 > 3/4
Question 140Single Answer
What is (3^{4} times 9^{2}) ?
A
36
B
38
C
310
D
96
Question 141Single Answer
If 34X-2 = 729, then find the value of X.
A
4
B
3
C
2
D
5
Question 142Single Answer
Convert 0.6 into fraction ?
A
3/5
B
2/3
C
4/5
Question 143Single Answer
The no. plate of a bus had peculiarity. The bus number was a perfect square. It was also a perfect square when the plate numbers were reversed. The bus company had only five hundred buses numbered from 1 to 500. What was the number ?
A
169
B
36
C
196
D
Can not say
Question 144Single Answer
If a and b are positive integers, such that ab = 125, then (a-b)a+b-4 = ?
A
16
B
25
C
28
D
30
Question 145Single Answer
If x*y = x2 + y2 – xy, then value of 9*11 is
A
93
B
103
C
60.5
D
121
Question 146Single Answer
Which is greater ?
A
15/16
B
17/18
C
Equal
D
Cannot compare
Question 147Single Answer
If sum of two numbers is 42 and their product is 437, then find their difference.
A
3
B
4
C
5
D
7
Question 148Single Answer
Write the 44000 in Roman numerals
A
XLI
B
XLVI
C
XLIV
D
XLVIC
Question 149Single Answer
Convert 0.0909… into fraction ?
A
1/11
B
9/11
C
1/9
D
9/10
Question 150Single Answer
What is (98 times 102) ?
A
9996
B
10000
C
10096
D
10196
Question 151Single Answer
Which is smaller ?
A
9/11
B
7/9
C
Equal
D
Cannot compare
Question 152Single Answer
Convert 0.5777… into fraction ?
A
26/45
B
52/90
C
13/22
D
5/9
Question 153Single Answer
Convert 0.81 into fraction ?
A
81/100
B
9/10
C
8/9
D
9/11
Question 154Single Answer
(63)2 – (12)2 =?
A
3528
B
3852
C
3582
D
3825
Question 155Single Answer
Which is greater ?
A
13/17
B
11/14
C
Equal
D
Cannot compare
Question 156Single Answer
16.928 + 24.7582 5.015 =?
A
20
B
24
C
22
D
26
Question 157Single Answer
Convert 0.75 into fraction ?
A
3/4
B
2/3
C
4/5
D
5/8
Question 158Single Answer
Which is greater ?
A
11/13
B
12/15
C
Equal
D
Cannot compare
Question 159Single Answer
Two numbers are co-prime if their HCF is ?
A
0
B
1
C
Same
D
Prime
Question 160Single Answer
Product of all factors of 10 is ?
A
10
B
100
C
1000
D
10000
Question 161Single Answer
How many real numbers exist between 2 and 3 ?
A
1
B
10
C
Infinite
D
None
Question 162Single Answer
Which number is divisible by 11 ?
A
12345
B
1331
C
1234
D
1213
Question 163Single Answer
What is the unit digit of (7^{245}) ?
A
1
B
3
C
7
D
9
Question 164Single Answer
What is (64^{2/3}) ?
A
4
B
8
C
16
D
32
Question 165Single Answer
What is (125^{1/3}) ?
A
3
B
4
C
5
D
6
Question 166Single Answer
Which of the following is composite ?
A
17
B
19
C
21
D
23
Question 167Single Answer
What is √0.0009 ?
A
0.003
B
0.03
C
0.3
D
0.09
Question 168Single Answer
What is √1156 ?
A
32
B
34
C
36
D
38
Question 169Single Answer
What is √2025 ?
A
35
B
40
C
45
D
50
Reasoning
Question 170Single Answer
‘Gram’ is relatd to ‘Mass’ in the same way as ‘Centimetre’ is related to
A
Area
B
Volume
C
Length
D
Sound
E
Energy
Question 171Single Answer
'Mustard' is related to 'Seed' in the same way as 'Carrot' is related to
A
Fruit
B
Stem
C
Flower
D
Root
E
None of these
Question 172Single Answer
Which of the following pairs of words have the same relationship as Fan : Heat?
A
Water : Drink
B
Light : Night
C
Teach : Student
D
Air : Breathe
E
Food : Hunger
Question 173Single Answer
'Radish' is related to 'Root', in the same way as 'Brinjal' is related to
A
Fruit
B
Stem
C
Flower
D
Root
E
None of these
Question 174Single Answer
'Jackal' is related to 'Carnivorous', in the same way as 'Goat' is related to
A
Omnivorous
B
Carnivorous
C
Herbivorous
D
Multivorous
E
None of these
Question 175Single Answer
Which of the following pairs has similar relationship as Run : Race?
A
Party : Dance
B
Study : Book
C
Lecture : Study
D
Enjoy : Journey
E
None of these
Question 176Single Answer
Which of the following has same relationship as that of Money : Wealth?
A
Pity : Kindness
B
Cruel : Anger
C
Wise : Education
D
Pride : Humility
E
None of these
Question 177Single Answer
Which of the following is related to ‘Melody’, in the same way as ‘Delicious’ is related to 'Taste'?
A
Memory
B
Highness
C
Tongue
D
Speak
E
Voice
Question 178Single Answer
Offhand’ is related to ‘Premeditation’ in the same way as ‘Above board’ is related to
A
Integrity
B
Honesty
C
Guide
D
Competition
E
None of these
Question 179Single Answer
5 : 7 : : ? : 28
A
20
B
14
C
56
D
26
E
None of these
Question 180Single Answer
Which one is different form the remaining three?
A
GIJK
B
DFGH
C
CEFG
D
ABCD
E
None of these
Question 181Single Answer
Three of the following four are alike in certain way and so form a group. Which is one that does not belong to the group?
A
71
B
73
C
77
D
67
E
None of these
Question 182Single Answer
Unscramble the letters in the given words and find the odd one out.
A
UMRSME
B
EIWNTR
C
PIGRSN
D
LCUOD
E
None of these
Question 183Single Answer
What should come next in the following number series?
0 2 4 6 2 3 0 2 4 6 4 5 0 2 4 6 6 7 0 2?
A
4
B
2
C
6
D
8
E
5
Question 184Single Answer
What will be there is the place of question mark in the following series?
E G 3 5, I K 9 9, M O 1 9 5, Q S 3 2 3?
A
UW483
B
ZA26
C
TU420
D
ST380
E
None of these
Question 185Single Answer
What should come next in the following letter series?
A Z A B Y A B C X A B C D W A B C D E V A B C D E
A
U
B
T
C
A
D
G
E
None of these
Question 186Single Answer
What should come next in the following letter series?
H G F E D C B A G F E D C B A G F E D C B
A
E
B
G
C
F
D
B
E
None of these
Question 187Single Answer
What should come next in the following letter series?
Z X V T R P N L J Y W U S Q O
A
M
B
K
C
H
D
J
E
None of these
Question 188Single Answer
Which of the following should come next in the given sequence of numbers?
24 3 2 4 3 1 2 4 3 1 2 2 4 3 1 2 3 1 2 3 2 4 3 1 2 3
A
2
B
3
C
4
D
5
E
None of these
Question 189Single Answer
What should come next in the following letter series?
P P O PO N PO N M P O N M L P O N M L
A
P
B
K
C
J
D
I
E
None of these
Question 190Single Answer
What should come next in the following number series?
9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 9 8 7 6 5 4 3 2 2 3 4 5 6 7 8
A
8
B
1
C
9
D
2
E
None of these
Question 191Single Answer
What should come next in the following number series?
3 4 4 3 4 4 5 3 4 4 5 6 3 4 4 5 6 7 3 4 4 5 6
A
4
B
5
C
6
D
7
E
None of these
Question 192Single Answer
What should come next in the following letter series?
A A B A B C A B C D A B C D E A B C D E F
A
A
B
G
C
H
D
B
E
None of these
Question 193Single Answer
What should come in the place of the question mark (?) in the following series of combination of alpha-numerals and symbols?Y 9B*W*D7*U5F?
A
S 3 H *
B
T#H*
C
T*#H
D
S*H5
E
SH*1
Question 194Single Answer
What should come next in the following number series?9 7 5 3 1 1 8 6 4 2 2 9 7 5 3 1 8 6 4 2 2 9 7 5 3 1 8 6 4 2 9 7 5 3 1 8 6 4 2 9 7 5
A
1
B
8
C
3
D
5
E
None of these
Question 195Single Answer
What should come next in the place of question mark(?) in the following letter sequence?AZB, CYD, EXF,?,IVJ, KUL
A
FYH
B
GWG
C
HWH
D
GUF
E
None of these
Question 196Single Answer
Four of the following five are alike in a certain way and so form a group. Which is the one that does not belong to that group?
A
215
B
143
C
247
D
91
E
65
Question 197Single Answer
Four of the following five are alike in a certain way and so form a group. Which is the one that does not belong to that group?
A
78
B
48
C
72
D
54
E
42
Question 198Single Answer
Four of the following five are alike in a certain way and so form a group. Which is the one that does not belong to that group?
A
45
B
51
C
39
D
93
E
85
Question 199Single Answer
Four of the following five are alike in a certain way and so form a group. Which is the one that does not belong to that group?